Nissan Frontier. Manual — part 209
CLUTCH PEDAL
CL-9
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
REMOVAL AND INSTALLATION
CLUTCH PEDAL
Exploded View
INFOID:0000000009478205
Removal and Installation
INFOID:0000000009478206
REMOVAL
1. Remove the clutch pedal bracket nuts from inside the engine compartment.
2. Disconnect the clutch interlock switch and ASCD clutch switch (if equipped), then remove the harness
from the pedal assembly.
3. Remove the snap pin and clevis pin.
4. Remove the pedal bracket bolt and then remove the clutch pedal assembly.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Tighten the pedal stopper bolt lock nut or ASCD clutch switch lock nut to the specified torque after installing
the clutch pedal assembly in the vehicle and adjusting the pedal free play.
Inspection
INFOID:0000000009478207
INSPECTION AFTER REMOVAL
• Inspect the clutch pedal for bends, damage, or cracked welds. Replace if necessary.
• Make sure that the assist spring and return spring have not lost their tension. Replace if necessary.
1.
Bracket
2.
Bushing
3.
Snap pin
4.
Pedal stopper rubber
5.
Clutch interlock switch
6.
Clutch pedal
7.
Stopper rubber
8.
ASCD clutch switch (if equipped)
9.
Pedal stopper bolt
10. Clevis pin
L.
Apply wheel bearing grease
AWDIA1131ZZ
CL-10
< REMOVAL AND INSTALLATION >
CLUTCH MASTER CYLINDER
CLUTCH MASTER CYLINDER
Exploded View
INFOID:0000000009478208
Removal and Installation
INFOID:0000000009478209
CAUTION:
Do not spill brake fluid onto painted surfaces. If it spills, wipe up immediately and wash the affected
area with water.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the snap pin and clevis pin from the clevis, and separate it from the clutch pedal.
2. Remove the hose clamp and hose from the clutch master cylinder.
3. Remove the clutch tube using suitable tool.
4. Remove the clutch master cylinder nuts, and remove the clutch master cylinder from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
• Before installation, check the position of the clevis and push rod. If
(L) is outside standard length, adjust the position of the clevis and
push rod.
• After installation, inspect and adjust the clutch pedal as necessary,
then bleed the clutch hydraulic system. Refer to
.
1.
Clamp
2.
Reservoir hose
3.
Clamp
4.
Cylinder body
5.
Clutch tube
A.
To reservoir tank
AWDIA0936GB
Length (L)
QR25DE
: 119.5 mm (4.70 in)
VQ40DE
: 120.5 mm (4.74 in)
SCIA5158E
CLUTCH RESERVOIR
CL-11
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
CLUTCH RESERVOIR
Removal and Installation
INFOID:0000000009478210
For removal and installation of clutch reservoir, refer to
BR-28, "Removal and Installation"
.
NOTE:
• Be sure to check clutch fluid after installation. Refer to
• Be sure to bleed clutch system after installation. Refer to
CL-12
< REMOVAL AND INSTALLATION >
OPERATING CYLINDER
OPERATING CYLINDER
Exploded View
INFOID:0000000009478211
Removal and Installation
INFOID:0000000009478212
CAUTION:
Do not spill brake fluid on painted surfaces. If it spills, wipe up immediately and wash the affected area
with water.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the clutch hose and copper sealing washer from the operating cylinder.
CAUTION:
Do not reuse copper sealing washer.
2. Remove the operating cylinder bolts, and remove the operating cylinder from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
• Tighten the clutch hose fitting to the specified torque.
CAUTION:
• Make sure the clutch hose is not bent or twisted.
• Do not reuse copper sealing washer.
• After installation, bleed the clutch hydraulic system. Refer to
.
1.
Operating cylinder
2.
Copper sealing washer
3.
Clutch hose
4.
Air bleeder
AWDIA0934GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст