Nissan Frontier. Manual — part 713
FUEL INJECTOR AND FUEL TUBE
EM-41
< REMOVAL AND INSTALLATION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
6. Remove fuel injector from fuel tube as follows:
a. Carefully open and remove clip.
b. Remove fuel injector from fuel tube by pulling straight.
CAUTION:
• Be careful with remaining fuel that may leak out from fuel
tube.
• Do not reuse O-rings.
• Do not damage fuel injector nozzles during removal.
• Do not bump or drop fuel injectors.
• Do not disassemble fuel injectors.
INSTALLATION
1. Install new O-rings to fuel injector, paying attention to the following.
CAUTION:
• Upper and lower O-rings are different colors.
• Handle O-ring with bare hands. Do not wear gloves.
• Lubricate O-ring with new engine oil.
• Do not reuse O-rings.
• Do not clean O-ring with solvent.
• Make sure that O-ring and its mating part are free of foreign material.
• When installing O-ring, be careful not to scratch it with tool or fingernails.
• Do not twist or stretch O-ring. If O-ring was stretched while it was being attached, allow it to
retract before inserting it into fuel tube.
• Insert new O-ring straight into fuel tube. Do not angle or twist it.
PBIC2999E
Fuel tube side
: Black
Nozzle side
: Green
EM-42
< REMOVAL AND INSTALLATION >
[QR25DE]
FUEL INJECTOR AND FUEL TUBE
2. Install fuel injector to fuel tube.
a. Insert clip into clip mounting groove on fuel injector.
• Insert new clip so that protrusion of fuel injector matches cut-
out of clip.
CAUTION:
• Do not reuse clip. Replace it with a new one.
• Do not reuse O-rings.
• Do not allow the clip to interfere with the O-ring. If interfer-
ence occurs, replace O-ring.
b. Insert the fuel injector into the fuel tube with the clip attached.
• Insert it while matching it to the axial center.
• Insert fuel injector so that protrusion of fuel tube matches cut-
out of clip.
• Make sure that fuel tube flange is securely fixed in flange fixing
groove on clip.
c.
Make sure that installation is complete by checking that the fuel
injector does not rotate or come off.
• Make sure that protrusions of the fuel injectors are aligned
with cutouts of clips after installation.
3. Install fuel tube and fuel injector assembly as follows:
CAUTION:
Do not let the tip of the injector nozzle come in contact with other parts.
a. Insert the tip of each fuel injector into intake manifold.
b. Tighten bolts in two steps in numerical order as shown.
4. Connect harness connectors to fuel injectors.
5. Install intake manifold. Refer to
EM-27, "Removal and Installation"
.
6. Connect quick connector at the engine side as follows:
a. Check the connection for foreign material and damage.
b. Align center to insert quick connector straight into fuel tube.
NOTE:
The figure shows the engine side as an example.
• Insert quick connector to fuel tube until the top spool on fuel
tube is inserted completely and the second level spool is posi-
tioned slightly below quick connector bottom end.
CAUTION:
• Hold (A) position as shown when inserting fuel tube into
quick connector.
• Do not reuse O-rings.
• Carefully align center to avoid inclined insertion to pre-
vent damage to O-ring inside quick connector.
• Insert until you hear a “click” sound and actually feel the engagement.
• To avoid misidentification of engagement with a similar sound, be sure to perform the next
step.
PBIC3000E
Fuel tube bolts
1st step
: 12.8 N·m (1.3 kg-m, 9 ft-lb)
2nd step
: 28.0 N·m (2.9 kg-m, 21 ft-lb)
PBIC2998E
KBIA0272E
FUEL INJECTOR AND FUEL TUBE
EM-43
< REMOVAL AND INSTALLATION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
c. Before clamping fuel feed hose with quick connector cap, pull quick connector hard by hand holding (A)
position. Make sure it is completely engaged (connected) so that it does not come out from fuel feed tube.
d. Install quick connector cap to quick connector connection.
(engine side)
• Install so that the arrow mark on the side faces up.
CAUTION:
• Make sure that quick connector and fuel tube are securely
fit into quick connector cap installation groove.
• If quick connector cap cannot be installed smoothly,
quick connector may have not been installed correctly.
Check the connection again.
7. Install fuel feed hose to hose clamp.
8. Installation is in the reverse order of removal after this step.
INSPECTION AFTER INSTALLATION
• Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to
MA-16, "FOR USA AND CANADA : Fluids and Lubricants"
(United
States and Canada).
• Use procedure below to check for fuel leakage.
• Turn ignition switch ON (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leak-
age at connection points.
• Start engine. With engine speed increased, check again for fuel leakage at connection points.
• Run engine to check for unusual noise and vibration.
NOTE:
If hydraulic pressure inside timing chain tensioner drops after removal and installation, slack in the guide
may generate a pounding noise during and just after engine start. However, this is normal. Noise will stop
after hydraulic pressure rises.
• Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gas, or any oils/fluids including
engine oil and engine coolant.
• Bleed air from passages in lines and hoses, such as in cooling system.
• After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to spec-
ified level, if necessary.
• Summary of the inspection items:
*Power steering fluid, brake fluid, etc.
PBIC2348E
Item
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leakage
Level
Engine oil
Level
Leakage
Level
Transmission/
transaxle fluid
A/T and CVT Models
Leakage
Level/Leakage
Leakage
M/T Models
Level/Leakage
Leakage
Level/Leakage
Other oils and fluids*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
Exhaust gas
—
Leakage
—
EM-44
< REMOVAL AND INSTALLATION >
[QR25DE]
INTAKE VALVE TIMING CONTROL
INTAKE VALVE TIMING CONTROL
Intake Valve Timing Control Solenoid Valve
INFOID:0000000009478063
REMOVAL
1. Disconnect harness connector from intake valve timing control solenoid valve.
2. Remove intake valve timing control solenoid valve bolt.
3. Remove intake valve timing control solenoid valve (1) and O-ring (2) from intake valve timing control sole-
noid valve cover.
CAUTION:
Do not reuse O-ring.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-rings.
• Lubricate the new O-ring for the intake valve timing control solenoid valve with clean engine oil
before installing.
AWBIA1007GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст