Nissan Frontier. Manual — part 270
DLK-126
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009478950
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tool
INFOID:0000000009478951
Tool number
(TechMech No.)
Tool name
Description
—
(J-39570)
Chassis Ear
Locating the noise
—
(J-50397)
NISSAN Squeak and Rattle Kit
Repairing the cause of noise
—
(J-43241)
Remote Keyless Entry Tester
Used to test key fobs
—
(J-50190)
Signal Tech II
• Activate and display TPMS transmitter
IDs
• Display tire pressure reported by the
TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
• Test remote keyless entry keyfob rela-
tive signal strength
kv48105501
(J-45295-A)
Transmitter activation tool
• Activate TPMS transmitter IDs
• Compatible with future sensors
• Equipped with a display (KV48105501
only)
SIIA0993E
ALJIA1232ZZ
LEL946A
ALEIA0131ZZ
ALEIA0183ZZ
PREPARATION
DLK-127
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
(TechMate No.)
Tool name
Description
(J-39565)
Engine Ear
Locating the noise
SIIA0995E
DLK-128
< REMOVAL AND INSTALLATION >
HOOD
REMOVAL AND INSTALLATION
HOOD
Fitting Adjustment
INFOID:0000000009478952
CLEARANCE AND SURFACE HEIGHT ADJUSTMENT
1. Remove the front grille. Refer to
EXT-23, "Removal and Installation"
2. Loosen the hood lock assembly and adjust the rubber bumpers until the surface height of the hood
becomes 1 mm (0.04 in) lower than the fender.
3. Engage the hood striker and temporarily tighten.
4. Check the lock and striker for looseness.
1.
Hood
2.
Front grille
3.
Front fender
4.
Headlamp assembly
D.
6.0 mm (0.24 in)
E.
0.7 mm (0.03 in)
F.
4.6 mm (0.18 in)
G.
0.0 mm (0.0 in)
H.
6.0 mm (0.24 in)
J.
0.7 mm (0.03 in)
AWKIA0543ZZ
HOOD
DLK-129
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5. Tighten the bolts to specification.
6. Adjust the surface height of the hood according to the fitting standard dimension by rotating right and left
rubber bumpers.
7. Install the front grille. Refer to
EXT-23, "Removal and Installation"
.
HOOD LOCK ADJUSTMENT
1. Remove the front grille. Refer to
EXT-23, "Removal and Installation"
2. Move the hood lock to the left or right so that striker (1) center is
vertically aligned with primary latch (4) center (when viewed
from vehicle front).
3. Make sure the secondary latch (3) is properly engaged with the
secondary striker (2) with hood's own weight by dropping it from
approximately 200 mm (7.87 in) height or by pressing it lightly
approximately 3 kg (29 N, 7 lb).
CAUTION:
Do not drop the hood from 300 mm (11.81 in) height or higher.
4. After adjusting hood lock, tighten the lock bolts to the specified
torque.
5. Install the front grille. Refer to
EXT-23, "Removal and Installation"
.
Removal and Installation of Hood Assembly
INFOID:0000000009478953
REMOVAL
1. Support the hood striker with suitable tool to prevent it from falling.
2. Remove the hinge nuts from the hood to remove the hood assembly.
CAUTION:
Operate with two workers, because of its heavy weight.
INSTALLATION
A
: More than 5.0 mm (0.197 in)
B
: 20 mm (0.79 in)
AWKIA1802ZZ
LIIA1701E
WIIA1055E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст