Nissan Frontier. Manual — part 316
DLN-166
< UNIT DISASSEMBLY AND ASSEMBLY >
[3S1330]
REAR PROPELLER SHAFT
Center Support Bearing
1. Remove the propeller shaft assembly from the vehicle. Refer to
DLN-163, "Removal and Installation"
2. Put matching marks on the propeller shaft tube and the slip
yoke.
CAUTION:
For matching marks, use paint. Do not damage the propel-
ler shaft tube or slip yoke.
3. Remove and discard the clamp near the center support bearing,
then slide the slip yoke off of propeller shaft tube.
4. Press the center support bearing off the propeller shaft tube
using Tool and suitable hydraulic press.
ASSEMBLY
Journal
1. Assemble the journal bearings. Apply multipurpose grease on
the bearing inner surface.
NOTE:
During assembly, use caution so that the needle bearings do not
fall down.
2. Select snap rings that will provide the specified play in an axial
direction of the journal, and install them. Refer to
.
CAUTION:
Do not reuse snap rings.
NOTE:
Select snap rings with a difference in thickness at both sides
within 0.02 mm (0.0008 in).
LDIA0151E
Tool number
: 205-D002
LDIA0152E
WPD019
APD012
REAR PROPELLER SHAFT
DLN-167
< UNIT DISASSEMBLY AND ASSEMBLY >
[3S1330]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
3. Adjust the thrust clearance between the bearing and snap ring
to zero by tapping the yoke.
4. Make sure that the journal moves smoothly and is below the
joint flex effort specification. Refer to
.
Center Support Bearing
1. Apply a thin coat of multi-purpose grease to both the propeller shaft tube and the inside surface of the
center support bearing.
2. Install the center support bearing on the propeller shaft tube
using a suitable pipe pressing on the inner race.
3. Install a new clamp over the boot on the slip yoke.
4. Align the matching marks and install the slip yoke on the propel-
ler shaft tube.
5. Clean the surfaces and position the boot over the propeller shaft tube and tighten the clamp.
SPD732
LDIA0119E
LDIA0153E
LDIA0151E
DLN-168
< UNIT DISASSEMBLY AND ASSEMBLY >
[3S1330]
REAR PROPELLER SHAFT
6. Install the center support bearing bracket, then install the rear
propeller shaft assembly in the vehicle. Refer to
WDIA0066E
SERVICE DATA AND SPECIFICATIONS (SDS)
DLN-169
< SERVICE DATA AND SPECIFICATIONS (SDS)
[3S1330]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000009479757
Snap Ring
INFOID:0000000009479758
Unit: mm (in)
*: Always check with the Parts Department for the latest parts information.
Applied model
VQ40DE
2WD
M/T short bed
A/T long bed
Propeller shaft model
3S1330
3
Flange type
Sleeve type
Number of joints
Coupling method with rear final drive
Coupling method with transmission
1st Shaft length (Center bearing to spider)
674.5
± 1.5 mm (26.56 ± 0.06 in)
741.5
± 1.5 mm (29.19 ± 0.06 in)
2nd Shaft length (Spider to spider)
783.8
± 1.5 mm (30.86 ± 0.06 in)
1152.8
± 1.5 mm (45.39 ± 0.06 in)
Shaft outer diameter
76.2 + 0.00/ - 0.13 mm (3.00 + 0.00/ - 0.01 in)
0.02 mm (0.0008 in) or less
0.6 mm (0.024 in) or less
2.26 N·m (0.23 kg-m, 20 in-lb) or less
Journal axial play
Propeller shaft runout limit
Propeller shaft joint flex effort
Thickness
Color
Part Number*
1.99 (0.0783)
White
37146-C9400
2.02 (0.0795)
Yellow
37147-C9400
2.05 (0.0807)
Red
37148-C9400
2.08 (0.0819)
Green
37149-C9400
2.11 (0.0831)
Blue
37150-C9400
2.14 (0.0843)
Light brown
37151-C9400
2.17 (0.0854)
Black
37152-C9400
2.20 (0.0866)
No paint
37153-C9400
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст