Nissan Frontier. Manual — part 1091
PRECAUTIONS
RAX-15
< SERVICE INFORMATION >
[M226]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SERVICE INFORMATION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010115392
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution
INFOID:0000000009478715
• When installing rubber parts, final tightening must be carried out under unladen condition* with tires
on ground.
* Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designated posi-
tions.
• After installing removed suspension parts, check wheel alignment and adjust if necessary.
RAX-16
< SERVICE INFORMATION >
[M226]
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009478716
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tool
INFOID:0000000009478717
Tool number
(TechMate No.)
Tool name
Description
205-D002
( — )
Bearing splitter
Removing axle shaft bearing
ZZA0700D
Tool name
Description
Power tool
Loosening nuts, screws and bolts
PIIB1407E
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
RAX-17
< SERVICE INFORMATION >
[M226]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009478718
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
Possible cause and SUSPECTED PARTS
Im
p
rop
er i
ns
ta
lla
tio
n,
lo
os
en
es
s
P
art
s interference
W
he
el be
arin
g da
ma
ge
PR
OP
EL
LE
R
S
H
A
F
T
REA
R
FINAL DRIVE
S
U
S
PENSION
TI
RE
S
ROAD W
H
EEL
BR
AK
E
S
Symptom
Noise
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Shudder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
×
RAX-18
< SERVICE INFORMATION >
[M226]
ON-VEHICLE SERVICE
ON-VEHICLE SERVICE
Rear Axle Parts
INFOID:0000000009478719
• Check the axle parts for excessive play, wear, and damage. Replace as necessary.
• Shake each rear wheel to check for excessive play. Repair as nec-
essary
• Retighten all nuts and bolts to the specified torque. Refer to
.
Rear Axle Bearing
INFOID:0000000009478720
• Check that the axle shaft bearing operates smoothly. Replace as necessary.
• Check for excessive axial end play.
SMA525A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст