Nissan Frontier. Manual — part 1268
ROAD TEST
TM-283
< PERIODIC MAINTENANCE >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
With CONSULT
Read the gear position.
Is downshifting correctly performed?
YES
>> GO TO 3.
NO
>> Record the malfunction, GO TO 3.
3.
CHECK ENGINE BRAKE
Check engine brake.
Does engine braking effectively reduce speed in 1
1
position?
YES
>> 1. Stop the vehicle.
2. Carry out the self-diagnostics. Refer to
TM-157, "CONSULT Function (TRANSMISSION)"
NO
>> Record the malfunction, then continue the trouble diagnosis.
TM-284
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
SHIFT CONTROL SYSTEM
REMOVAL AND INSTALLATION
SHIFT CONTROL SYSTEM
Exploded view
INFOID:0000000009480677
Removal and Installation
INFOID:0000000009480678
REMOVAL
1. Remove instrument lower panel RH and glove box. Refer to
IP-24, "Removal and Installation"
2. Remove the center console. Refer to
.
3. Disconnect the following from the shift selector assembly.
• Shift selector control cable
• Key interlock cable
• Shift selector harness connector
4. Remove the shift selector assembly.
1.
Shift selector handle button
2.
Shift selector handle spring
3.
Shift selector handle
4.
Overdrive control switch
5.
Position indicator
6.
Position lamp
7.
Shift selector harness connector
8.
Shift selector control cable
9.
Lock plate
10. Key interlock cable
11. Shift selector assembly
WCIA0503E
SHIFT CONTROL SYSTEM
TM-285
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5. Remove the shift selector handle, if necessary.
6. Remove the position indicator, if necessary.
INSTALLATION
Installation is in the reverse order of removal.
• Install and adjust the shift selector control cable. Refer to
TM-285, "Inspection and Adjustment"
.
• Install and adjust the key interlock cable. Refer to
TM-297, "Removal and Installation"
Inspection and Adjustment
INFOID:0000000009480679
ADJUSTMENT
1. Loosen nut of shift selector control cable (A).
2. Place the manual lever (B) and shift selector handle in “P” posi-
tion.
3. Push the shift selector control cable in the direction shown with a
force of 9.8 N (1kg, 2.2 lb), and release it. This is in the natural
state, tighten shift selector control cable nut (A) to specifications.
INSPECTION
With the shift selector handle in the “P” position, turn the ignition switch to the ON position with the engine
OFF.
Confirm that the following conditions apply.
• The shift selector handle can be moved from the “P” position only when the brake pedal is depressed.
• The shift selector handle stops at each position with the feel of engagement when it is moved through all the
positions.
• There is no excessive effort, sticking, noise or rattle.
• The actual position of the shift selector handle matches the position shown by the shift position indicator and
the A/T body.
• The back-up lamps illuminate only when the shift selector handle is placed in the “R” position.
• The back-up lamps do not illuminate when the shift selector handle is pushed against the “R” position when
in the “P” or “N” position.
• The engine can only be started with the shift selector handle in the “P” and “N” positions.
• The A/T is locked completely when shift selector handle is in the “P” position.
Shift selector control
cable nut (A)
: 14.7 N·m (1.5 kg-m, 11 ft-lb)
AWDIA0755ZZ
TM-286
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
OIL PAN
OIL PAN
Removal and Installation
INFOID:0000000009480680
REMOVAL AND INSTALLATION
Removal
1. Drain A/T fluid. Refer to
TM-271, "Changing the A/T Fluid
2. Remove oil pan bolts.
3. Remove oil pan and gasket.
4. Check for foreign materials in oil pan to help determine cause of malfunction. If the A/T fluid is very dark,
has some burned smell, or contains foreign particles then friction material (clutches, band) may need
replacement. A tacky film that will not wipe clean indicates varnish build up. Varnish can cause valves,
servo, and clutches to stick and can inhibit pump pressure.
CAUTION:
If friction material is detected, flush the transmission cooler after repair. Refer to
5. Remove magnets from oil pan.
Installation
1. Install the oil pan magnets as shown.
SCIA2308E
SCIA5200E
SCIA5200E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст