Nissan Frontier. Manual — part 1112
FRONT SEAT BELT
SB-7
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
Crew Cab Models
Removal and Installation
INFOID:0000000009482272
REMOVAL OF SEAT BELT RETRACTOR - KING CAB
CAUTION:
• Before servicing SRS, turn the ignition switch off, disconnect both battery terminals and wait at least
three minutes.
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes. Refer to
83, "Removal and Installation"
2. Remove the rear door finishers. Refer to
INT-15, "Removal and Installation"
.
3. Remove the retractor anchor bolt, retractor bolt upper, then remove the retractor and belt assembly.
• On RH side, disconnect the seat belt tension sensor.
4. Disconnect the harness connector from the seat belt pre-tensioner.
CAUTION:
WHIA0344E
1.
Center pillar upper finisher
2.
D-ring anchor
3.
D-ring anchor bolt cover
4.
Seat belt retractor and belt assembly
(RH)
5.
Seat belt lower anchor
(RH) (seat belt tension
sensor)
6.
Seat belt tension sensor connector
7.
Anchor cover (RH)
8.
Anchor cover (LH)
9.
Seat belt lower anchor (LH)
10. Center pillar lower finisher
11. Seat belt pre-tensioner
connector
12. Seat belt retractor and belt assembly (LH)
13. Center pillar
14. Seat belt height adjuster
A.
Height adjuster anchor bolt
B.
D-ring anchor bolt
C.
Seat belt lower anchor bolt D.
Retractor anchor bolt
E.
Retractor bolt upper
Front
SB-8
< REMOVAL AND INSTALLATION >
FRONT SEAT BELT
• For installing/removing seat belt pre-tensioner connector,
insert a thin screwdriver wrapped in tape into the notch,
lift the lock and remove the connector.
• Install the connector with the lock raised, and push the
lock into the connector.
INSTALLATION OF SEAT BELT RETRACTOR - KING CAB
CAUTION:
Hold belt tension sensor harness away from being caught or twisted during installation.
Installation is in the reverse order of removal.
• Install the seat belt retractor upper bolt first.
• Ensure that seat belt height adjuster is locked in the lowest position during installation.
REMOVAL OF SEAT BELT RETRACTOR - CREW CAB
CAUTION:
• Before servicing SRS, turn the ignition switch off, disconnect both battery terminals and wait at least
three minutes.
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes. Refer to
83, "Removal and Installation"
.
2. Remove the center pillar upper/lower finishers. Refer to
INT-19, "Removal and Installation"
.
3. Remove the seat belt retractor and belt bolts and assembly.
• On RH side, disconnect the seat belt tension sensor.
4. Disconnect the harness connector from the seat belt pre-tensioner.
CAUTION:
• For installing/removing seat belt pre-tensioner connector,
insert a thin screwdriver wrapped in tape into the notch,
lift the lock and remove the connector.
• Install the connector with the lock raised, and push the
lock into the connector.
INSTALLATION OF SEAT BELT RETRACTOR - CREW CAB
CAUTION:
Hold belt tension sensor harness away from being caught or twisted during installation.
Installation is in the reverse order of removal.
• Install the seat belt retractor and belt assembly upper bolt first.
• Ensure that seat belt height adjuster is locked in the lowest position during installation.
REMOVAL OF SEAT BELT BUCKLE
1. Remove the front seat. Refer to
SE-32, "Removal and Installation"
PHIA0341E
PHIA0341E
FRONT SEAT BELT
SB-9
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
2. Remove screw and seat cushion inner finisher.
3. Remove the anchor bolt and buckle.
4. Disconnect the buckle switch connector from the seat connector.
INSTALLATION OF SEAT BELT BUCKLE
Installation is in the reverse order of removal.
WHIA0128E
SB-10
< REMOVAL AND INSTALLATION >
REAR SEAT BELT
REAR SEAT BELT
Exploded View
INFOID:0000000009482273
KING CAB MODELS
LHIA0096E
1.
Seat belt bracket
2.
Seat belt retractor and belt assembly
3.
Seat belt lower anchor
4.
Seat belt buckle
5.
D-ring anchor bolt cover
6.
D-ring anchor
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст