Nissan Frontier. Manual — part 312
DLN-150
< SYSTEM DESCRIPTION >
[PROPELLER SHAFT: 3S1310]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYSTEM DESCRIPTION
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009479744
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
(front)
(rear)
(front)
(rear)
(front)
(rear)
"
Possible cause and suspected parts
Une
ven
rot
a
tion
torq
ue
Rot
ati
on
im
ba
la
nc
e
Ex
ce
ss
iv
e run
ou
t
Di
ffere
n
tial
Axle
Su
sp
en
si
on
Ti
re
s
Road wheel
Driv
e sh
af
t
Brak
es
S
tee
ring
Symptom
Noise
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
PROPELLER SHAFT ASSEMBLY
DLN-151
< BASIC INSPECTION >
[PROPELLER SHAFT: 3S1310]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
BASIC INSPECTION
PROPELLER SHAFT ASSEMBLY
Inspection
INFOID:0000000009479745
APPEARANCE AND NOISE INSPECTION
Check the propeller shaft tube surface for dents or cracks. If damaged, replace the propeller shaft assembly.
PROPELLER SHAFT VIBRATION
If a vibration is present at high speed, inspect the propeller shaft runout first.
1. Measure the runout of the propeller shaft tube at several points
by rotating the final drive companion flange with your hands.
2. If the runout exceeds specifications, disconnect the propeller shaft at the final drive companion flange;
then rotate the companion flange 90
°, 180° and 270° and reconnect the propeller shaft.
3. Check the runout again. If the runout still exceeds specifications, replace the propeller shaft assembly.
4. After installation, check for vibration by driving vehicle.
Propeller shaft runout limit
2WD Refer
DLN-158, "General Specification"
LDIA0161E
LDIA0121E
DLN-152
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 3S1310]
REAR PROPELLER SHAFT
UNIT REMOVAL AND INSTALLATION
REAR PROPELLER SHAFT
Removal and Installation
INFOID:0000000009479746
COMPONENTS
Model 3S1310
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove under cover (if equipped). Refer to
EXT-15, "Removal and Installation"
.
2. Put the transmission in neutral and release the parking brake.
3. Put matching marks on the rear propeller shaft flange yoke and
the rear final drive companion flange as shown.
CAUTION:
For matching marks, use paint. Do not damage the rear pro-
peller shaft flange yoke or the companion flange.
4. Remove the bolts, then remove the propeller shaft from the rear
final drive and transmission.
INSPECTION
AWDIA1081ZZ
1.
Propeller shaft (1st shaft)
2.
Snap ring
3.
Journal bearing
4.
Sleeve yoke (5A/T)
5.
Journal
6.
Propeller shaft (2nd shaft)
7.
Flange yoke
8.
Sleeve yoke (5M/T)
Front
WDIA0049E
REAR PROPELLER SHAFT
DLN-153
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 3S1310]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Inspect the propeller shaft runout. If runout exceeds the limit,
replace the propeller shaft assembly.
• While holding the flange yoke on one side, check axial play of the
joint as shown. If the journal axial play exceeds the specification,
repair or replace the journal parts.
• Check the propeller shaft for dents or cracks. If damage is
detected, replace the propeller shaft assembly.
INSTALLATION
Installation is in the reverse order of removal.
• After installation, check for vibration by driving the vehicle. Refer to
DLN-150, "NVH Troubleshooting Chart"
.
CAUTION:
Do not reuse the bolts and nuts. Always install new ones.
Propeller shaft runout limit
2WD : Refer to
LDIA0121E
Journal axial play : Refer to
LDIA0117E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст