Nissan Frontier. Manual — part 201
CHG
DIAGNOSIS AND REPAIR WORKFLOW
CHG-7
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
YES
>> GO TO 4.
NO
>> GO TO 10.
4.
INSPECTION WITH CHARGE WARNING LAMP (IDLING)
Start the engine and run it at idle
Does the charge warning lamp turn OFF?
YES
>> GO TO 5.
NO
>> GO TO 6.
5.
INSPECTION WITH CHARGE WARNING LAMP (ENGINE AT 2,500 RPM)
Increase and maintain the engine speed at 2,500 rpm.
Does the charge warning lamp illuminate?
YES
>> GO TO 8.
NO
>> Inspection End.
6.
“L” TERMINAL CIRCUIT (SHORT) INSPECTION
Check terminal “L” circuit for (short). Refer to
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair as needed.
7.
“S” TERMINAL CIRCUIT INSPECTION
Check terminal “S” circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair as needed.
8.
MEASURE “B” TERMINAL VOLTAGE
Start engine. With engine running at 2,500 rpm, measure “B” terminal voltage.
What voltage does the measurement result show?
Less than 13.0 V>>GO TO 9.
More than 16.0 V>>Replace generator. Refer to
CHG-28, "Removal and Installation - QR25DE Models"
or
CHG-29, "Removal and Installation - VQ40DE Models"
.
9.
“B” TERMINAL CIRCUIT INSPECTION
Check “B” terminal circuit. Refer to
Is the inspection result normal?
YES
>> Replace generator. Refer to
CHG-28, "Removal and Installation - QR25DE Models"
or
"Removal and Installation - VQ40DE Models"
NO
>> Repair as needed.
10.
INSPECTION WITH CHARGE WARNING LAMP (IGNITION SWITCH IS ON)
1. Disconnect generator connector and apply ground to “L” terminal.
2. Turn the ignition switch ON.
Does the charge warning lamp illuminate?
YES
>> Replace generator. Refer to
CHG-28, "Removal and Installation - QR25DE Models"
or
"Removal and Installation - VQ40DE Models"
NO
>> GO TO 11.
11.
CHECK “L” TERMINAL CIRCUIT (OPEN)
Check “L” terminal circuit (OPEN). Refer to
.
>> Repair as needed.
CHG-8
< SYSTEM DESCRIPTION >
CHARGING SYSTEM
SYSTEM DESCRIPTION
CHARGING SYSTEM
System Diagram
INFOID:0000000009482309
System Description
INFOID:0000000009482310
The generator provides DC voltage to operate the vehicle's electrical system and to keep the battery charged.
The voltage output is controlled by the IC regulator.
Component Description
INFOID:0000000009482311
ALMIA0207GB
Component part
Description
Generator
Terminal “1”
Refer to
Terminal “2”
Refer to
Terminal “3”
Refer to
.
Terminal “4”
Used for the power generation voltage variable control system.
Refer to
.
Combination meter (Charge warning lamp)
The IC regulator warning function activates to illuminate the
charge warning lamp if any of the following symptoms occur while
generator is operating:
• Excessive voltage is produced.
• No voltage is produced.
IPDM E/R
Used for the power generation voltage variable control system.
Refer to
.
CHG
POWER GENERATION VOLTAGE VARIABLE CONTROL SYSTEM
CHG-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
POWER GENERATION VOLTAGE VARIABLE CONTROL SYSTEM
System Diagram
INFOID:0000000009482312
System Description
INFOID:0000000009482313
Power generation variable voltage control system has been adopted. By varying the voltage to the generator,
engine load due to power generation of the generator is reduced and fuel consumption is decreased.
NOTE:
When any malfunction is detected in the power generation variable voltage control system, power generation
is performed according to the characteristic of the IC regulator in the generator.
Component Description
INFOID:0000000009482314
ALMIA0057GB
Component part
Description
Battery current sensor
The battery current sensor is installed on the battery cable at the
negative terminal. The battery current sensor detects the charg-
ing/discharging current of the battery and sends a voltage signal
to the ECM according to the current value detected.
ECM
The battery current sensor detects the charging/discharging cur-
rent of the battery. The ECM judges the battery condition based on
this signal.
The ECM judges whether to request more output via the power
generation voltage variable control according to the battery condi-
tion.
When performing the power generation voltage variable control,
the ECM calculates the target power generation voltage according
to the battery condition and sends the calculated value as the pow-
er generation command value to the IPDM E/R.
IPDM E/R
The IPDM E/R converts the received power generation command
value into a pulse width modulated (PWM) command signal and
sends it to the IC regulator.
Generator (IC regulator)
The IC regulator controls the power generation voltage by the tar-
get power generation voltage based on the received PWM com-
mand signal.
When there is no PWM command signal, the generator performs
the normal power generation according to the characteristic of the
IC regulator.
CHG-10
< DTC/CIRCUIT DIAGNOSIS >
CHARGING SYSTEM PRELIMINARY INSPECTION
DTC/CIRCUIT DIAGNOSIS
CHARGING SYSTEM PRELIMINARY INSPECTION
Diagnosis Procedure
INFOID:0000000009482315
1.
CHECK BATTERY TERMINALS CONNECTION
Check if battery terminals are clean and tight.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair battery terminal connection. Confirm repair by performing complete Charging system test
using EXP-800 NI or GR8-1200 NI (if available). Refer to the applicable Instruction Manual for
proper testing procedures.
2.
CHECK FUSE
Check for blown fuse and fusible link.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the blown fuse or fusible link after repairing the affected circuit.
3.
CHECK GENERATOR GROUND TERMINAL CONNECTION
Check if connector E209 terminal 5 is clean.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair connection.
4.
CHECK DRIVE BELT TENSION
Check drive belt tension. Refer to
CHG-28, "Removal and Installation - QR25DE Models"
or
"Removal and Installation - VQ40DE Models"
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair as needed.
Unit
Power source (Power supply terminals)
Fuse or Fusible Link
Generator
Battery (terminal 3)
Fuse 30
Battery (terminal 1)
Fusible Link A
Combination meter
Ignition switch ON (terminal 2)
Fuse 14
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст