Qashqai J11. Front suspension — part 2
FRONT STABILIZER
FSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
FRONT STABILIZER
Exploded View
INFOID:0000000010297078
1.
Strut mounting insulator
2.
Strut mounting bearing
3.
Bound bumper
4.
Coil spring
5.
Lower rubber seat
6.
Strut
7.
Steering knuckle
8.
Stabilizer connecting rod
9.
Stabilizer clamp
E1EIA0115GB
FSU-18
< REMOVAL AND INSTALLATION >
FRONT STABILIZER
Removal and Installation
INFOID:0000000010297079
REMOVAL
1.
Remove tires from vehicle.
2.
Remove the engine side under cover.
3.
Set suitable jack under front suspension member.
4.
Remove stabilizer connecting rod. Refer to
5.
Remove steering outer socket from steering knuckle. Refer to
.
6.
Remove front exhaust mount.
7.
Remove catalytic converter.
8.
Remove rear torque rod. Refer to
9.
Remove front suspension member stay and rubber stopper from vehicle.
10. Gradually lower jack front suspension member in order to
remove stabilizer mounting bolts.
11. Remove mounting bolts (
) of stabilizer clamp, and then
remove stabilizer clamp and stabilizer bushing from front sus-
pension member.
12. Remove stabilizer bar.
INSTALLATION
Install in the reverse order of removal.
• Install stabilizer clamp so that notch (A) is facing front of vehicle
(
⇐
).
• Install stabilizer bushing so that slit (B) is facing front of vehicle
(
⇐
).
• Install the stabilizer clamp bolts.
10. Stabilizer bushing
11. Stabilizer bar
12. Front suspension member
13. Rebound stopper rubber
14. Front suspension member stay
15. Transverse link
16. Rear suspension member stay
17. Front suspension member insulator
Refer to
for symbols in the figure.
WEIA0181E
WEIA0182E
JPEIA0058ZZ
FRONT STABILIZER
FSU-19
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
• To connect the stabilizer connecting rod (1), tighten the nut while
holding the hexagonal part (A) on the stabilizer connecting rod.
• Perform the final tightening of the nuts and bolts under unladen conditions with the tires on level ground.
• Perform inspection after installation.
Inspection
INFOID:0000000010297080
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if necessary.
Stabilizer clamps :
60 N.m (6.1 kg-m; 44 ft-lb)
Stabilizer connecting rod :
84 N.m (8.6 kg-m; 62 ft-lb)
JPEIA0252ZZ
FSU-20
< REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000010297081
1.
Strut mounting insulator
2.
Strut mounting bearing
3.
Bound bumper
4.
Coil spring
5.
Lower rubber seat
6.
Strut
7.
Steering knuckle
8.
Stabilizer connecting rod
9.
Stabilizer clamp
E1EIA0115GB
FRONT SUSPENSION MEMBER
FSU-21
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
Removal and Installation
INFOID:0000000010297082
REMOVAL
1.
Remove tires from vehicle.
2.
Remove under cover from vehicle.
3.
Remove the bolt and separate the front wheel sensor from steering knuckle. Separate the harness from
the brackets and position aside. Refer to
BRC-138, "FRONT WHEEL SENSOR : Exploded View"
.
CAUTION:
• Failure to separate the front wheel sensor from the steering knuckle may result in damage to the
front wheel sensor.
• Pull out the front wheel sensor, being careful to turn it as little as possible. Do not pull on wheel
sensor harness.
4.
Remove the nut and separate the stabilizer connecting rod from the strut bracket.
5.
Remove the cotter pin and nut, and separate the outer socket from the steering knuckle.
6.
Remove the bolt and separate steering column yoke from steering gear. Refer to
7.
Remove transverse link from steering knuckle. Refer to
(2WD), Refer to
8.
Remove rear torque rod. Refer to
(K9K),
9.
Set suitable jack front suspension member.
10. Remove front suspension member stay from vehicle. Refer to
.
11. Remove mounting bolts and nuts of front suspension member.
12. Gradually lower jack to remove front suspension assembly from
vehicle.
CAUTION:
Secure suspension assembly to suitable jack while remov-
ing it.
13. Remove mounting bolts and nuts, and then remove transverse
link, stabilizer bar from front suspension member.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install the suspension member bolts in the order shown.
- 1-2 temporary tightening3-5 torque to specification Refer to
• Perform final tightening of installation position between front sus-
pension member and transverse links (rubber bushing) under
unladen condition with tires on level ground.
• Check wheel sensor harness for proper connection.
Inspection
INFOID:0000000010297083
INSPECTION AFTER REMOVAL
Check the front suspension member for significant deformation, cracks, or damages. Replace it if necessary.
INSPECTION AFTER INSTALLATION
10. Stabilizer bushing
11. Stabilizer bar
12. Front suspension member
13. Rebound stopper rubber
14. Front suspension member stay
15. Transverse link
16. Rear suspension member stay
17. Front suspension member insulator
Refer to
WEIA0181E
⇐
: Front
ALEIA0222ZZ
FSU-22
< REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
1.
Check wheel alignment. Refer to
FSU-7, "Wheel Alignment Inspection"
.
2.
Adjust the neutral position of the steering angle sensor. Refer to
SERVICE DATA AND SPECIFICATIONS (SDS)
FSU-23
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000010297084
For Europe
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
For Russie
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Tire size
215/65R16
215/60R17
225/45R19
Camber
Degree minute (Decimal degree)
Minimum
–1
°
15
′
(–1.25
°
)
Nominal
–0
°
30
′
(–0.50
°
)
Maximum
0
°
15
′
(0.25
°
)
Left and right difference
0
°
36
′
(0.60
°
) or less
Caster
Degree minute (Decimal degree)
Minimum
4
°
55
′
(4.92
°
)
Nominal
5
°
40
′
(5.67
°
)
Maximum
6
°
25
′
(6.42
°
)
Left and right difference
0
°
36
′
(0.60
°
) or less
Kingpin inclination
Degree minute (Decimal degree)
Minimum
10
°
00
′
(10.00
°
)
Nominal
10
°
45
′
(10.75
°
)
Maximum
11
°
30
′
(11.50
°
)
Total toe-in
Distance
Minimum
In 2 mm (0.08 in)
Nominal
In 3 mm (0.12 in)
Maximum
In 4 mm (0.16 in)
Angle
Degree minute (Decimal degree)
Minimum
In 0
°
04
′
(0.07
°
)
Nominal
In 0
°
10
′
(0.17
°
)
Maximum
In 0
°
16
′
(0.27
°
)
Tire size
215/65R16
215/60R17
225/45R19
Camber
Degree minute (Decimal degree)
Minimum
–1
°
05
′
(–1.08
°
)
–1
°
10
′
(–1.17
°
)
Nominal
–0
°
20
′
(–0.33
°
)
–0
°
25
′
(–0.42
°
)
Maximum
0
°
25
′
(0.42
°
)
0
°
20
′
(0.33
°
)
Left and right difference
0
°
36
′
(0.60
°
) or less
Caster
Degree minute (Decimal degree)
Minimum
4
°
50
′
(4.83
°
)
4
°
45
′
(4.75
°
)
Nominal
5
°
35
′
(5.58
°
)
5
°
30
′
(5.50
°
)
Maximum
6
°
20
′
(6.33
°
)
6
°
15
′
(6.25
°
)
Left and right difference
0
°
36
′
(0.60
°
) or less
Kingpin inclination
Degree minute (Decimal degree)
Minimum
9
°
45
′
(9.75
°
)
9
°
50
′
(9.83
°
)
Nominal
10
°
30
′
(10.50
°
)
10
°
35
′
(10.58
°
)
Maximum
11
°
15
′
(11.25
°
)
11
°
20
′
(11.33
°
)
Total toe-in
Distance
Minimum
In 2 mm (0.08 in)
Nominal
In 3 mm (0.12 in)
Maximum
In 4 mm (0.16 in)
Angle
Degree minute (Decimal degree)
Minimum
In 0
°
04
′
(0.07
°
)
Nominal
In 0
°
10
′
(0.17
°
)
Maximum
In 0
°
16
′
(0.27
°
)
FSU-24
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
For GOM / SAF / Australia
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Ball Joint
INFOID:0000000010297085
Wheelarch Height
INFOID:0000000010478352
Measure value under unladen* conditions.
Tire size
215/65R16
215/60R17
225/45R19
Camber
Degree minute (Decimal degree)
Minimum
–1
°
15
′
(–1.25
°
)
Nominal
–0
°
30
′
(–0.50
°
)
Maximum
0
°
15
′
(0.25
°
)
Left and right difference
0
°
36
′
(0.60
°
) or less
Caster
Degree minute (Decimal degree)
Minimum
4
°
40
′
(4.67
°
)
4
°
45
′
(4.75
°
)
Nominal
5
°
25
′
(5.42
°
)
5
°
30
′
(5.50
°
)
Maximum
6
°
10
′
(6.17
°
)
6
°
15
′
(6.25
°
)
Left and right difference
0
°
36
′
(0.60
°
) or less
Kingpin inclination
Degree minute (Decimal degree)
Minimum
10
°
00
′
(10.00
°
)
Nominal
10
°
45
′
(10.75
°
)
Maximum
11
°
30
′
(11.50
°
)
Total toe-in
Distance
Minimum
In 2 mm (0.08 in)
Nominal
In 3 mm (0.12 in)
Maximum
In 4 mm (0.16 in)
Angle
Degree minute (Decimal degree)
Minimum
In 0
°
04
′
(0.07
°
)
Nominal
In 0
°
10
′
(0.17
°
)
Maximum
In 0
°
16
′
(0.27
°
)
Swing torque
Transverse link
0.5 – 3.4 N·m (0.06 – 0.34 kg-m, 5 – 30 in-lb)
Measurement on spring balance
Transverse link
13.5 – 91.9 N (1.4 – 9.4 kg, 3 – 21 lb)
Axial end play
0 mm (0 in)
Applied model
H5FT
Destination
Europe / SAF / GOM
Russie
Tire size
215/65R16
215/60R17
225/45R19
215/65R16
215/60R17
225/45R19
Front (Hf)
760 mm
(29.92 in)
759 mm
(29.88 in)
770 mm
(30.31 in)
769 mm
(30.28 in)
SFA746B
SERVICE DATA AND SPECIFICATIONS (SDS)
FSU-25
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
*: 90% Fuel. Engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Measure value under unladen* conditions.
*: 90% Fuel. Engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Measure value under unladen* conditions.
*: 90% Fuel. Engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Measure value under unladen* conditions.
*: 90% Fuel. Engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Applied
model
MR20DD
Destination
Russie 6MT
Russie CVT
SAF / GOM / Australia
Tire size
215/65R16
215/60R17
225/45R19
215/65R16
215/60R17
225/45R19
215/65R16
215/60R17
225/45R19
Front (Hf)
769 mm
(30.28 in)
768 mm
(30.24 in)
767 mm
(30.20 in)
767 mm
(30.20 in)
765 mm
(30.12 in)
766 mm
(30.16 in)
758 mm
(29.84 in)
759 mm
(29.88 in)
Applied model
K9K
Destination
Europe
SAF / GOM
Tire size
215/65R16
215/60R17
225/45R19
215/60R17
225/45R19
Front (Hf)
758 mm
(29.84 in)
759 mm
(29.88 in)
758 mm
(29.84 in)
Applied
model
R9M
Destination
Europe / Australia
Russie
SAF / GOM
Tire size
215/65R16
215/60R17
225/45R19
215/60R17
225/45R19
215/65R16
215/60R17
225/45R19
Front (Hf)
756 mm
(29.76 in)
755 mm
(29.72 in)
770 mm
(30.31 in)
756 mm
(29.76 in)
755 mm
(29.72 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст