Nissan Pathfinder (2012 year). Manual — part 594
CONTROL VALVE WITH TCM
TM-179
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
10. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the manual valve notch and
manual plate height. Remove it vertically.
11. Remove plug (1) with bracket (2) from control valve with TCM.
•
:Bolt
12. Remove the bracket (1) from plug (2).
13. Remove O-ring (1) from plug (2).
CAUTION:
Do not reuse O-ring.
SCIA5142E
JSDIA1311ZZ
JSDIA1312ZZ
JSDIA1313ZZ
August 2012
2012 Pathfinder
TM-180
< REMOVAL AND INSTALLATION >
CONTROL VALVE WITH TCM
14. Remove O-ring from A/T assembly harness connector.
CAUTION:
Do not reuse O-ring.
15. Disconnect TCM connectors.
CAUTION:
Do not damage connectors.
16. Remove A/T assembly harness connector from control valve
with TCM using suitable tool.
17. Disconnect TCM connector (1) and transmission range switch
connector (2).
CAUTION:
Do not damage connectors.
Installation
CAUTION:
After completing installation, check for A/T fluid leaks and fluid level. Refer to
.
SCIA5155E
SCIA5447E
SCIA5448E
JSDIA1317ZZ
August 2012
2012 Pathfinder
CONTROL VALVE WITH TCM
TM-181
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1. Connect TCM connector (1) and transmission range switch con-
nector (2).
2. Install A/T assembly harness connector to control valve with
TCM.
3. Connect TCM connector.
4. Install new O-ring in A/T assembly harness connector.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
5. Install new O-ring (1) in plug (2).
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
• O-ring should be free of contamination.
JSDIA1317ZZ
SCIA5450E
SCIA5447E
SCIA5155E
JSDIA1313ZZ
August 2012
2012 Pathfinder
TM-182
< REMOVAL AND INSTALLATION >
CONTROL VALVE WITH TCM
6. Install plug (2) to bracket (1).
7. Install plug (1) [with bracket (2)] to control valve with TCM.
•
:Bolt
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
8. Install control valve with TCM in transmission case.
CAUTION:
• Make sure that input speed sensor is securely installed
into input speed sensor hole (A).
• Hang down output speed sensor harness toward outside
so as not to disturb installation of control valve with TCM.
• Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
• Assemble it so that manual valve cutout is engaged with
manual plate projection.
9. Install bolts (A), (B) and (C) in control valve with TCM.
JSDIA1312ZZ
JSDIA1311ZZ
(1)
: Brake band
JSDIA1318ZZ
SCIA5142E
: Front
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8074E
August 2012
2012 Pathfinder
CONTROL VALVE WITH TCM
TM-183
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
10. Tighten bolt (1A), (2B) and (3A) temporarily to prevent disloca-
tion. After that tighten them in order (1
→
2
→
3). Then tighten
other bolts. Tighten control valve with TCM bolts to the specified
torque.
11. Connect output speed sensor connector (1).
12. Securely fasten output speed sensor (1) harness with terminal
clip (
).
13. Install oil pan to transmission case. Refer to
TM-174, "Removal and Installation"
.
14. Pull up A/T assembly harness connector.
CAUTION:
Do not damage connector.
: Front
Bolt symbol
A
B
C
Number of bolts
5
6
1
Length mm (in)
42 (1.65)
55 (2.17)
40 (1.57)
Tightening torque
N·m (kg-m, in-lb)
7.9 (0.81, 70)
With ATF applied
7.9 (0.81, 70)
SCIA8075E
JSDIA1319ZZ
JSDIA1316ZZ
SCIA5038E
August 2012
2012 Pathfinder
TM-184
< REMOVAL AND INSTALLATION >
CONTROL VALVE WITH TCM
15. Install snap ring to A/T assembly harness connector.
16. Connect A/T assembly harness connector.
17. Connect the negative battery terminal.
18. Refill the A/T with fluid and check the fluid level and for fluid
leaks. Refer to
TM-157, "Checking the A/T Fluid (ATF)"
SCIA5039E
August 2012
2012 Pathfinder
REAR OIL SEAL
TM-185
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REAR OIL SEAL
Removal and Installation
INFOID:0000000007357307
REMOVAL
1. Remove rear propeller shaft. Refer to
DLN-329, "Removal and Installation"
2. Remove transfer from transmission (4WD models). Refer to
DLN-153, "Removal and Installation"
(ATX14B),
DLN-287, "Removal and Installation"
(TX15B).
3. Remove rear oil seal using suitable tool.
CAUTION:
Do not scratch rear extension assembly (2WD models) or
adapter case assembly (4WD models).
INSTALLATION
1. Install new rear oil seal until it is flush into the rear extension
case (2WD models) using Tool or adapter case (4WD models)
using suitable tool.
CAUTION:
• Apply ATF to rear oil seal.
• Do not reuse rear oil seal.
2. Install transfer to transmission (4WD models). Refer to
153, "Removal and Installation"
(ATX14B),
(TX15B).
3. Install rear propeller shaft. Refer to
(2S1330) or
DLN-340, "Removal and Installation"
(2S1350).
4. Check the A/T fluid level and for fluid leaks. Refer to
SCIA5254E
Tool number
: ST33400001 (J-26082)
WCIA0475E
August 2012
2012 Pathfinder
TM-186
< REMOVAL AND INSTALLATION >
KEY INTERLOCK CABLE
KEY INTERLOCK CABLE
Component
INFOID:0000000007357308
CAUTION:
• Install key interlock cable in such a way that it will not be damaged by sharp bends, twists or interfer-
ence with adjacent parts.
• After installing key interlock cable to control device, make sure that casing cap and bracket are
firmly secured in their positions. If casing cap can be removed with an external load of less than 39
N (4.0 kg, 8.8 lb), replace key interlock cable with new one.
Removal and Installation
INFOID:0000000007357309
REMOVAL
1. Remove the center console. Refer to
IP-22, "Removal and Installation"
.
2. Remove instrument lower panel LH. Refer to
IP-20, "Removal and Installation"
.
WCIA0467E
August 2012
2012 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст