Nissan Pathfinder (2012 year). Manual — part 178
HOOD
DLK-319
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Be careful not to bend the cable too much, keep the radius
100mm (3.94 in) or more.
2. Make sure the cable is not offset from the grommet, and push
the grommet into the lower dash panel hole securely.
3. Apply sealant around the grommet at * mark.
4. Install the cable securely to the lock.
5. Adjust the hood lock. Refer to
.
6. Install the front grille. Refer to
EXT-20, "Removal and Installation"
.
Hood Lock Control Inspection
INFOID:0000000007355652
CAUTION:
If the hood lock cable is bent or deformed, replace it.
1. Remove the front grille. Refer to
EXT-20, "Removal and Installation"
2. Make sure the secondary latch is properly engaged with the sec-
ondary striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height.
3. While operating the hood opener, carefully make sure the front
end of the hood is raised by approx. 20 mm (0.79 in). Also make
sure the hood opener returns to the original position.
4. Check the hood lock lubrication condition. If necessary, apply
“body grease” to the points shown.
5. Install the front grille. Refer to
EXT-20, "Removal and Installation"
.
LIIA1698E
LIIA1699E
PIIA1086E
PIIA0176E
August 2012
2012 Pathfinder
2012 Pathfinder
DLK-320
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR
DOOR
Fitting Adjustment
INFOID:0000000007355653
FRONT DOOR
Longitudinal clearance and surface height adjustment at front end
1. Remove the fender. Refer to
EXT-22, "Removal and Installation"
2. Loosen the hinge bolts.
3. Raise or lower the front door at rear end to adjust.
4. Tighten the hinge bolts.
5. Install the fender. Refer to
EXT-22, "Removal and Installation"
REAR DOOR
Longitudinal clearance and surface height adjustment at front end
1. Remove the center pillar lower finisher. Refer to
INT-19, "Removal and Installation"
2. Loosen the lower hinge bolts.
3. From inside the vehicle, loosen the upper hinge nuts. Open the door, and raise or lower the rear end of the
door to adjust.
4. Tighten the lower hinge bolts.
5. Install the center pillar lower finisher. Refer to
INT-19, "Removal and Installation"
.
BACK DOOR
Longitudinal clearance and surface height adjustment
A.
4.5
±
1.0 mm (0.177
±
0.039 in)
WIIA0732E
August 2012
2012 Pathfinder
2012 Pathfinder
DOOR
DLK-321
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1. Open and support the back door.
2. Slightly loosen the hinge nuts.
3. Reposition the door as necessary and tighten the nuts.
4. Confirm the adjustment. Repeat as necessary to obtain the desired fit.
STRIKER ADJUSTMENT
Body Side Doors
1. Loosen the striker bolts.
1.
Back door assembly
2.
Back door hinge
3.
Rear Combination lamp
4.
Rear bumper fascia
5.
Roof
6.
Side window glass
a.
7.2
±
2.0 mm (0.28
±
0.08 in)
b.
6.0
±
1.5 mm (0.24
±
0.06 in)
c.
2.0
±
2.0 mm (0.08
±
0.08 in)
d.
1.0
±
1.5 mm (0.04
±
0.06 in)
e.
8.0
±
1.5 mm (0.31
±
0.06 in)
f.
5.3
±
2.0 mm (0.21
±
0.08 in)
g.
0.8
±
2.0 mm (0.03
±
0.08 in)
h.
0.8
±
1.0 mm (0.03
±
0.04 in)
j.
2.0
±
1.0 mm (0.08
±
0.04 in)
WIIA0733E
August 2012
2012 Pathfinder
2012 Pathfinder
DLK-322
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR
2. Adjust the striker so that it becomes parallel with the lock inser-
tion direction.
3. Tighten the striker bolts to specification.
Back Door
1. Loosen the striker bolts.
2. Adjust the striker so that it becomes parallel with the lock inser-
tion direction.
3. Tighten the striker bolts to specification.
Removal and Installation
INFOID:0000000007355654
CAUTION:
• When removing and installing a door assembly, support the door with a jack and shop cloth to pro-
tect the door and body.
• When removing and installing a door assembly, be sure to carry out the fitting adjustment.
• Check the hinge rotating point for poor lubrication. If necessary, apply “body grease”.
FRONT DOOR
Removal
1. Remove the front door glass and regulator. Refer to
GW-15, "Front Door Glass Regulator"
2. Remove the door harness.
3. Remove the check link bolt from the hinge pillar.
AWKIA1766ZZ
WIIA0735E
Check link to hinge pillar
bolt
14.7 N·m (1.5 kg-m, 11 ft-lb)
LIIA1726E
August 2012
2012 Pathfinder
2012 Pathfinder
DOOR
DLK-323
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4. Remove the door-side hinge nuts, and the door assembly.
Installation
Installation is in the reverse order of removal.
Align the front door. Refer to
.
REAR DOOR
Removal
1. Remove the door finisher. Refer to
INT-15, "Removal and Installation"
.
2. Remove the inner seal.
3. Remove the rear door speaker. Refer to
AV-38, "Removal and Installation"
AV-260, "Removal and Installation of Rear Door Speaker"
(BOSE AUDIO WITHOUT NAVIGATION) or
AV-425, "Removal and Installation of Rear Door Speaker"
(BOSE AUDIO WITH NAVIGATION).
4. Remove the rear door tweeter. Refer to
AV-426, "Removal and Installation of Rear Tweeter"
AUDIO WITH NAVIGATION).
5. Remove the rear door glass and regulator. Refer to
GW-19, "Rear Door Glass Regulator"
.
6. Remove the door harness.
7. Remove the check link bolt from the hinge pillar.
8. Remove the door-side hinge nuts, and remove the door assem-
bly.
Installation
Installation is in the reverse order of removal.
Align the rear door. Refer to
BACK DOOR
Removal
Door hinge nuts
24.5 N·m (2.5 kg-m, 18 ft-lb)
LIIA1727E
Check link to hinge pillar
bolt
14.7 N·m (1.5 kg-m, 11 ft-lb)
LIIA1726E
Door hinge nuts
25.8 N·m (2.6 kg-m, 19 ft-lb)
LIIA1727E
August 2012
2012 Pathfinder
2012 Pathfinder
DLK-324
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR
1. Remove the glass hatch. Refer to
GW-24, "Removal and Installation"
.
2. Remove the license lamp finisher. Refer to
EXT-23, "Removal and Installation"
.
3. Remove the back door lock assembly. Refer to
DLK-330, "Component Structure"
4. Remove the back door wire harness.
5. Remove the rear wiper motor. Refer to
WW-75, "Removal and Installation"
6. Remove the rear washer nozzle and hose from the back door. Refer to
7. Remove the high mounted stop light. Refer to
EXL-151, "High-Mounted Stop Lamp"
.
8. Support the back door.
9. Remove the back door stays.
10. Remove the door side nuts and the back door assembly.
CAUTION:
Two technicians should be used to avoid damaging the back door during removal.
Installation
Installation is in the reverse order of removal.
Align the rear door. Refer to
Back Door Stay Disposal
INFOID:0000000007355655
1. Fix back door stay (1) using a vise (C).
2. Using hacksaw (A) slowly make 2 holes in the back door stay, in
numerical order as shown in the figure.
CAUTION:
• When cutting a hole on back door stay, always cover a
hacksaw using a shop cloth (B) to avoid scattering metal
fragments or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
WIIA1056E
JMKIA3336ZZ
August 2012
2012 Pathfinder
2012 Pathfinder
DOOR
DLK-325
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
A: 20 mm (0.787 in)
B: Cut at the groove.
JMKIA3609ZZ
August 2012
2012 Pathfinder
2012 Pathfinder
DLK-326
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
FRONT DOOR LOCK
Component Structure
INFOID:0000000007355656
Removal and Installation
INFOID:0000000007355657
REMOVAL
1. Remove the front door window regulator. Refer to
GW-15, "Front Door Glass Regulator"
2. Remove door side grommet, and remove door key cylinder
assembly (driver side) or outside handle escutcheon (passenger
side) bolts (1) (T30) from grommet hole.
• (2) Weatherstrip
3. While pulling the outside handle (1), remove door key cylinder
assembly or escutcheon (2).
1.
Grommet
2.
Front door striker
3.
Door lock assembly
4.
Outside handle cable
5.
Inside handle assembly
6.
Inside handle cable
7.
Door lock cable
8.
Key cylinder rod (Driver side only)
9.
Door key cylinder
10. Outside handle bracket
11. Front gasket
12. Outside handle
13. Door key cylinder assembly (Driver
side) Outside handle escutcheon
(Passenger side)
14. Rear gasket
Vehicle front
AWKIA1793GB
AWKIA2017ZZ
ALKIA0956ZZ
August 2012
2012 Pathfinder
2012 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст