Nissan Pathfinder (2012 year). Manual — part 442
ILLUMINATION
INL-57
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ABLIA3370GB
August 2012
2012 Pathfinder
INL-58
< SYMPTOM DIAGNOSIS >
INTERIOR LIGHTING SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
INTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000007355250
CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected.
Symptom
Possible cause
Inspection item
All of the following lamps do not turn ON
• Front room/map lamp assembly
• Personal lamp 2nd row (with personal lamp 2nd
row)
• Room lamp 2nd row (without personal lamp 2nd
row)
• Cargo room lamp
• Vanity mirror lamps (if equipped)
• Ignition keyhole illumination
• Harness between BCM and each in-
terior room lamp
• Harness between BCM and each
door switch
• BCM
Battery saver output/power supply cir-
cuit
Refer to
.
Some or all of the following interior room lamps do
not turn ON/OFF
• Front room/map lamp assembly
• Personal lamp 2nd row (with personal lamp 2nd
row)
• Room lamp 2nd row (without personal lamp 2nd
row)
• Harness between BCM and each in-
terior room lamp
• BCM
Door switch circuit
Refer to
(without Intelligent
Key system).
Interior room lamp control circuit
Refer to
.
Cargo lamp does not turn ON/OFF
• Harness between BCM and cargo
lamp
• BCM
Cargo lamp circuit
Refer to
.
Ignition keyhole illumination does not turn ON/OFF
• Harness between BCM and cargo
lamp
• BCM
Ignition keyhole illumination circuit
Refer to
Interior room lamp timer does not activate.
(It turns ON/ OFF when the door opens/closes.)
—
Check the interior room lamp setting.
Refer to
.
Interior room lamp battery saver does not activate.
—
Check the interior room lamp battery
saver setting.
Refer to
.
August 2012
2012 Pathfinder
PRECAUTIONS
INL-59
< PRECAUTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007355251
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000007355252
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″
LOCK
″
position.
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing work. If
DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the
″
ACC
″
position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
August 2012
2012 Pathfinder
INL-60
< PRECAUTION >
PRECAUTIONS
5. When the repair work is completed, return the ignition switch to the
″
LOCK
″
position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT.
Precaution for Work
INFOID:0000000007355253
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components.
- Water soluble dirt: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the dirty
area.
Then rub with a soft and dry cloth.
- Oily dirt: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the dirty area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.
• Do not use organic solvent such as thinner, benzene, alcohol, or gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.
August 2012
2012 Pathfinder
PREPARATION
INL-61
< PREPARATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000007355254
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-46534)
Trim tool set
For removing trim
AWJIA0483ZZ
August 2012
2012 Pathfinder
INL-62
< REMOVAL AND INSTALLATION >
INTERIOR ROOM LAMP
REMOVAL AND INSTALLATION
INTERIOR ROOM LAMP
Removal and Installation
INFOID:0000000007355255
FRONT ROOM/MAP LAMP ASSEMBLY
Removal
The front room/map lamp assembly is replaced as part of the over-
head console assembly. Refer to
INT-22, "Removal and Installation"
.
: Metal clip
: Vehicle front
Installation
Installation is in the reverse order of removal.
Bulb Replacement
1. Using a suitable tool (A), remove front room/map lamp assembly
lens (1).
: Pawl
: Vehicle front
CAUTION:
Wrap a cloth around suitable tool to protect the housing
and lens.
2. Release one side of the bulb (2) from the tab, then pull straight
downward to remove.
VANITY MIRROR LAMP (IF EQUIPPED)
Removal
ALLIA0581ZZ
Front room/map lamp as-
sembly bulb
: 12V - 8W
AWLIA1667ZZ
August 2012
2012 Pathfinder
INTERIOR ROOM LAMP
INL-63
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
The vanity mirror lamp is replaced as part of the sun visor assembly.
INT-22, "Removal and Installation"
.
Installation
Installation is in the reverse order of removal.
Bulb Replacement
The vanity mirror lamp bulb is replaced as part of the sun visor assembly. Refer to
PERSONAL LAMP (IF EQUIPPED)
Removal
1. Release the clips and remove personal lamp from headlining.
INT-22, "Removal and Installation"
: Pawl
: Metal clip
2. Disconnect personal lamp electrical connector, then remove
from overhead console.
Installation
Installation is in the reverse order of removal.
Bulb Replacement
1. Remove personal lamp.
2. Using a suitable tool (A), release the pawls and remove per-
sonal lamp lens (1).
CAUTION:
Wrap a cloth around suitable tool to protect the housing
and lens.
3. Release one side of the bulb (2) from the tab, then pull straight
downward to remove.
ROOM LAMP (IF EQUIPPED)
Removal
ALLIA0583ZZ
ALLIA0588ZZ
Personal lamp bulb
: 12V - 8W
AWLIA1669ZZ
August 2012
2012 Pathfinder
INL-64
< REMOVAL AND INSTALLATION >
INTERIOR ROOM LAMP
1. Using a suitable tool (A), release the pawls and remove the
room lamp lens (1).
: Pawl
CAUTION:
Wrap a cloth around suitable tool to protect the housing
and lens.
2. Remove room lamp screws (2).
3. Disconnect the connector, then remove room lamp.
Installation
Installation is in the reverse order of removal.
Bulb Replacement
1. Using a suitable tool, release the pawls and remove the room lamp lens.
2. Release the room lamp bulb retainers (1), then pull bulb (2)
straight out to remove.
CARGO LAMP
Removal
AWLIA1670ZZ
Room lamp bulb
: 12V - 8W
ALLIA0326ZZ
August 2012
2012 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст