Nissan Pathfinder (2012 year). Manual — part 525
SE-40
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
Conventional Passenger Seat
19. Headrest holder with multi position
lock
20. Headrest holder
21. Lumbar support lever knob
22 Snap ring
AWJIA0552ZZ
1.
Damper assembly
2.
Headrest
3.
Seatback assembly
4.
Switch assembly
5.
Power seat switch escutcheon
6.
Recliner switch knob
7.
Slide switch knob
8.
Seat cushion assembly
9.
Seat cushion outer cover
10. Leg cover
11. Seat cushion front finisher
12. Passenger seat wiring harness
13. Power seat frame assembly
14. Seat cushion inner finisher
15. Seat belt buckle assembly
16. Leg cover
17. Seat cushion rear finisher
18. Manual seat frame assembly
August 2012
2012 Pathfinder
FRONT SEAT
SE-41
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Fold Flat Passenger Seat
Seatback Assembly
INFOID:0000000007356074
REMOVAL
CAUTION:
19. Recline lever
20. Seat cushion rear finisher
21. Seatback board
22. Headrest holder with multi position
lock
23. Headrest holder
AWJIA0553ZZ
1.
Front seatback lever
2.
Trim clip
3.
Headrest
4.
Seatback assembly
5.
Seat cushion assembly
6.
Seat cushion outer finisher
7.
Leg cover
8.
Seat frame assembly
9.
Passenger seat wiring harness
10. Seat cushion inner cover
11. Leg cover
12. Seat belt buckle assembly
13. Inboard reclining arm outer cover
14. Inboard reclining arm inner cover
15. Outboard reclining arm inner cover
16. Outboard reclining arm outer cover
17. Seat cushion rear finisher
18. Seatback board
19. Headrest holder with multi position
lock
20. Headrest holder
August 2012
2012 Pathfinder
SE-42
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
Seats equipped with side air bags can only be serviced as an assembly.
1. Remove the seat assembly. Refer to
SE-33, "Removal and Installation"
.
2. Unzip the seatback trim flap (1).
3. Unclip the lower retainer (2).
4. For the passenger seatback, remove the seatback board from the seatback. Refer to
.
5. Unclip the seatback trim J-clips.
6. Remove the bolts (two for each side) and the seatback assem-
bly.
DISASSEMBLY
CAUTION:
Seats equipped with side air bags can only be serviced as an assembly.
1. Remove the seatback assembly.
2. Remove the headrest.
LIIA2419E
SIIA0113E
LIIA2420E
August 2012
2012 Pathfinder
FRONT SEAT
SE-43
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
3. From inside of the seatback, squeeze the headrest holder tabs
at the base of the stay pipe and pull up to remove.
NOTE:
Before installing the headrest holder, check its orientation (front/
rear and right/left).
4. Remove the snap ring and the lumbar support lever knob.
5. Remove the seatback trim and pad assembly.
6. Remove the hog rings to separate the seatback trim from the pad and the heating element (if equipped).
ASSEMBLY
Assembly is in the reverse order of disassembly.
INSTALLATION
Installation is in the reverse order of removal.
Passenger Seatback Board
INFOID:0000000007356075
SOFT SEATBACK
Removal
1. The seatback board is attached to the seat frame with the follow-
ing:
• Two top tabs (A)
• Two side tabs (B)
• Two bottom clips (C) (must be replaced)
2. Move seat to forward position.
LRS023
PIIA1156E
ALIIA0366ZZ
August 2012
2012 Pathfinder
SE-44
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
3. Hold the seatback board as shown and pull the top of the seat-
back board away from the seat back frame.
4. Pull the middle part of the seatback board to disengage the side
tabs (A) from the seatback frame.
5. Pull the lower part of the seatback board to disengage the bot-
tom clips from the seatback frame.
Installation
Installation is in the reverse order of removal.
HARD SEATBACK
Removal
1. The seatback board is attached to the seat frame with the follow-
ing:
• Two top tabs (A)
• Two side tabs (B)
• Two bottom clips (C) (must be replaced)
2. Move seat to forward position.
3. Hold the seatback board as shown and pull the bottom of the
seatback board away from the seat back frame.
ALIIA0368ZZ
ALIIA0367ZZ
ALIIA0369ZZ
ALIIA0370ZZ
August 2012
2012 Pathfinder
FRONT SEAT
SE-45
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
4. Pull the middle part of the seatback board to disengage the side
tabs (A) from the seatback frame.
5. Lift the upper part of the seatback board to disengage the top
tabs from the seatback frame.
Installation
Installation is in the reverse order of removal.
Seat Cushion Trim and Pad
INFOID:0000000007356076
REMOVAL
CAUTION:
• Front passenger seat is equipped with an Occupant Classification System sensor and control mod-
ule. Do not disassemble front passenger seat cushion assembly or remove the trim as this will affect
the Occupant Classification System calibration.
• Always replace passenger seat cushion as an assembly.
• When removed, the passenger seat cushion must always be placed pan side UP to prevent damage.
• During installation, the wire harness clips must be reinstalled in the holes they were originally in. Do
not add additional clips.
• The Occupant Classification System control module can only be replaced as part of the seat cushion
assembly.
1. Remove the front seat assembly. Refer to
SE-33, "Removal and Installation"
.
2. Remove the power seat switch knobs and power seat switch
escutcheon (if equipped) or lift knobs on manual seats.
3. Remove the seat cushion outer finisher.
4. Remove the power seat switch screws.
5. Remove four bolts and the seat cushion assembly.
ALIIA0371ZZ
LIIA0681E
LIIA0285E
August 2012
2012 Pathfinder
SE-46
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
• On the fold flat passenger seat it is necessary to unclip the
rear flap j-clip from the seat pan.
6. Remove the retainer on the seat cushion frame, then remove the harness connector for the seat cushion
heater (if equipped).
DISASSEMBLY
CAUTION:
• Front passenger seat is equipped with an Occupant Classification System sensor and control mod-
ule. Do not disassemble front passenger seat cushion assembly or remove the trim as this will affect
the Occupant Classification System calibration.
1. Remove the seat cushion assembly.
2. On the drivers seat only, remove the hog rings to separate the trim cover from the pad and seat cushion
heater unit.
ASSEMBLY
Assembly is in the reverse order of disassembly.
INSTALLATION
Installation is in the reverse order of removal.
SIIA0503E
August 2012
2012 Pathfinder
REAR SEAT
SE-47
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
REAR SEAT
Exploded View
INFOID:0000000007356077
Disassembly and Assembly
INFOID:0000000007356078
Second Row Outer
AWJIA0788GB
August 2012
2012 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст