Nissan Pathfinder (2012 year). Manual — part 382
EXT-18
< REMOVAL AND INSTALLATION >
REAR BUMPER
REAR BUMPER
Removal and Installation
INFOID:0000000007355990
REMOVAL
1. Remove the LH and RH rear combination lamps. Refer to
EXL-153, "Removal and Installation"
2. Remove the mudguards (if equipped). Refer to
EXT-26, "Removal and Installation"
.
3. Remove the rear fender protectors. Refer to
EXT-25, "Removal and Installation of Rear Fender Protector"
.
4. Remove the LH and RH rear fascia strut lower bolts.
5. Remove the rear fascia lower stay bolts.
6. Remove the fascia front upper bolts near the wheel opening.
7. Release the left pinch rail clips and remove the LH side of rear bumper fascia from the quarter panel.
8. Release the right pinch rail clips and remove the RH side of the rear bumper fascia from the quarter panel.
9. Remove the fascia rear upper bolts near the rear combination lamps LH/RH.
10. Remove the rear bumper fascia.
11. Disconnect the harness on left side of tow hitch.
12. Detach the INTELLIGENT-KEY antenna, if equipped from the rear bumper reinforcement, then remove
rear bumper reinforcement.
13. Remove the drafter duct from the lower side of LH quarter panel.
14. Remove the rear valance nuts and bolts, then remove the rear valance.
INSTALLATION
Installation is in the reverse order of removal.
1.
Rear valance
2.
Rear bumper reinforcement
3.
Rear bumper fascia
4.
Rear fascia strut LH/RH
5.
Step pad
6.
Clip
7.
Tow hitch
8.
Tow harness bracket
9.
Tow hitch harness
10. Rear fascia lower stay (LH shown)
11. Pinch rail
12. Washer
13. Drafter duct
14. Filter element
Vehicle front
AWKIA1743ZZ
August 2012
2012 Pathfinder
REAR BUMPER
EXT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
• Apply sealant to clips securing upper step pad during installation.
Units: mm (in)
1.
Rear bumper fascia
2.
Bed side outer LH
3.
Rear combination lamp
4.
Step pad
5.
Back door
ALKIA1952ZZ
Portion
Measurement
Standard
Difference (MAX)
A-A
E
Clearance
0.0 (0.000)
+ 1.0 (0.039)
F
Surface height
0.8 (0.031)
+ 1.0 (0.039)
B–B
G
Clearance
0.0 (0.000)
±
1.0 (0.039)
H
Surface height
0.8 (0.031)
±
1.0 (0.039)
C-C
J
Clearance
3.0 (0.118)
±
1.5 (0.059)
D-D
K
Clearance
7.2 (0.283)
±
2.0 (0.079)
August 2012
2012 Pathfinder
EXT-20
< REMOVAL AND INSTALLATION >
FRONT GRILLE
FRONT GRILLE
Removal and Installation
INFOID:0000000007355991
REMOVAL
1. Remove the upper clips from the front grille.
2. Twist and release the LH and RH side clips and release the top of the front grille.
3. Detach the lower front grille clips and remove the front grille.
4. Remove the front emblem, if necessary.
INSTALLATION
Installation is in the reverse order of removal.
1.
Front grille
2.
Front emblem
A.
Clips CG101
B.
Clips C205
Vehicle front
AWKIA1511ZZ
August 2012
2012 Pathfinder
COWL TOP
EXT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
COWL TOP
Removal and Installation
INFOID:0000000007355992
REMOVAL
1. Remove the front wiper arms. Refer to
WW-70, "Removal and Installation"
.
2. Remove the cowl top seal.
3. Remove the cowl top clips C103 and lift the cowl top, disconnect the washer tubes from the washer noz-
zles and remove the cowl top.
4. Release the clips C205 and remove the LH and RH cowl top extensions.
INSTALLATION
Installation is in the reverse order of removal.
1.
Cowl top extension RH
2.
Cowl top
3.
Cowl top seal
4.
Cowl top extension LH
A.
Clip C205
B.
Clip C103
C.
Grommet CF110
Vehicle front
AWKIA0063ZZ
August 2012
2012 Pathfinder
EXT-22
< REMOVAL AND INSTALLATION >
FRONT FENDER
FRONT FENDER
Removal and Installation
INFOID:0000000007355993
REMOVAL
1. Remove the LH and RH headlamp assemblies. Refer to
EXL-145, "Removal and Installation"
.
2. Remove the front fender protector. Refer to
.
3. Remove the mudguard (if equipped). Refer to
EXT-27, "Removal and Installation"
.
4. Remove the front bumper fascia. Refer to
EXT-15, "Removal and Installation"
.
5. Remove the hood prop rod and hood prop rod hold down clip.
6. Remove the front fender bolts from hoodledge and the dash panel.
7. Remove the front fender bolts from the rocker panel and the radiator core support member.
8. Remove the front fender.
INSTALLATION
Installation is in the reverse order of removal.
AWKIA0086GB
August 2012
2012 Pathfinder
LICENSE LAMP FINISHER
EXT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
LICENSE LAMP FINISHER
Removal and Installation
INFOID:0000000007355994
REMOVAL
1. Remove the back door finisher. Refer to
INT-27, "Removal and Installation"
2. Remove the vapor barrier plastic.
3. Remove the license lamp finisher nuts and remove the license lamp finisher.
INSTALLATION
Installation is in the reverse order of removal.
1.
Back door
2.
License lamp finisher
A.
License lamp finisher nuts
AWKIA0065ZZ
August 2012
2012 Pathfinder
EXT-24
< REMOVAL AND INSTALLATION >
FENDER PROTECTOR
FENDER PROTECTOR
Component
INFOID:0000000007355995
Front Fender Protector
Rear Fender Protector
WIIA1078E
1.
Front fender protector LH shown
2.
J-Nuts
3.
Clip C205
4.
Plastic clips
Vehicle front
AWKIA1924ZZ
1.
Rear fender protector RH
2.
Clips C103
3.
J-Nuts
4.
Rear fender protector LH
Vehicle front
August 2012
2012 Pathfinder
FENDER PROTECTOR
EXT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation of Front Fender Protector
INFOID:0000000007355996
REMOVAL
1. Remove the front mudguard (if equipped). Refer to
EXT-27, "Removal and Installation"
2. Remove the screws.
3. Remove the plastic clips.
4. Remove the front fender protector.
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation of Rear Fender Protector
INFOID:0000000007355997
REMOVAL
1. Remove the rear mudguard (if equipped). Refer to
EXT-27, "Removal and Installation"
.
2. Remove the screws.
3. Remove the plastic clips.
4. Remove the rear fender protector.
INSTALLATION
Installation is in the reverse order of removal.
August 2012
2012 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст