Nissan Pathfinder (2012 year). Manual — part 20
NORMAL OPERATING CONDITION
ADP-145
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
NORMAL OPERATING CONDITION
Description
INFOID:0000000007356234
The following symptoms are normal operations, and they do not indicate a malfunction.
Symptom
Cause
Action to take
Reference page
Entry/Exit assist function does
not operate.
No initialization has been performed.
Perform initialization.
Entry/exit assist function is disabled.
NOTE:
The entry/exit assist function is disabled
before delivery (initial setting).
Change the settings.
Entry assist function does not op-
erate.
Manual operation with power seat switch
was performed after exit assist function
execution.
Perform the memory
function.
Memory function, entry/exit as-
sist function or Intelligent Key in-
terlock function does not
operate.
The operating conditions are not fulfilled.
Fulfill the operation
conditions.
Memory function:
Exit assist function:
Entry assist function:
Intelligent Key interlock
function:
August 2012
2012 Pathfinder
ADP-146
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007356235
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000007356236
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″
LOCK
″
position.
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing work. If
DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the
″
ACC
″
position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
August 2012
2012 Pathfinder
PRECAUTIONS
ADP-147
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
5. When the repair work is completed, return the ignition switch to the
″
LOCK
″
position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT.
Precaution for Work
INFOID:0000000007356237
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components.
- Water soluble dirt: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the dirty
area.
Then rub with a soft and dry cloth.
- Oily dirt: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the dirty area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.
• Do not use organic solvent such as thinner, benzene, alcohol, or gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.
August 2012
2012 Pathfinder
ADP-148
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000007829398
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-46534)
Trim tool set
Removing trim components
AWJIA0483ZZ
August 2012
2012 Pathfinder
DRIVER SEAT CONTROL UNIT
ADP-149
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
REMOVAL AND INSTALLATION
DRIVER SEAT CONTROL UNIT
Removal and Installation
INFOID:0000000007356238
SE-33, "Removal and Installation"
for removal and installation of driver seat control unit from driver
seat.
August 2012
2012 Pathfinder
ADP-150
< REMOVAL AND INSTALLATION >
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
Removal and Installation
INFOID:0000000007356239
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1. Remove the battery negative terminal. Refer to
PG-76, "Removal and Installation"
2. Remove the instrument lower panel LH using a suitable tool. Refer to
IP-12, "Removal and Installation"
.
3. Remove the automatic drive positioner control unit screw (A).
4. Separate automatic drive positioner control unit (1) from bracket
and disconnect electrical connectors.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Clamp the harness in position.
NOTE:
After installing the automatic drive positioner control unit, perform additional service when disconnecting bat-
tery negative terminal. Refer to
ADP-10, "Special Repair Requirement"
.
ALIIA0210GB
August 2012
2012 Pathfinder
SEAT MEMORY SWITCH
ADP-151
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
SEAT MEMORY SWITCH
Removal and Installation
INFOID:0000000007356240
Refer to
INT-15, "Removal and Installation"
for removal and installation of seat memory switch from the door
finisher.
August 2012
2012 Pathfinder
ADP-152
< REMOVAL AND INSTALLATION >
DOOR MIRROR REMOTE CONTROL SWITCH
DOOR MIRROR REMOTE CONTROL SWITCH
Removal and Installation
INFOID:0000000007356241
Refer to
for removal and installation of door mirror remote control switch from instru-
ment lower panel LH.
August 2012
2012 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст