Nissan Sentra. Manual — part 274
DLK-212
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
COMPONENT PARTS
REMOTE KEYLESS ENTRY SYSTEM : Component Parts Location
INFOID:0000000009756531
REMOTE KEYLESS ENTRY SYSTEM : Component Description
INFOID:0000000009756532
TRUNK LID OPENER SYSTEM
1.
BCM
(view with instrument panel removed)
2.
IPDM E/R
3.
Remote keyless entry receiver
(view with instrument panel removed)
4.
Front door switch LH
(RH similar)
5.
Rear door switch LH
(RH similar)
6.
Key switch
7.
Horn relay
8.
Horn
ALKIA2953ZZ
Item
Function
BCM
Controls the door lock function.
Door lock and unlock switch
Input lock or unlock signal to BCM.
Door switch
Input door open/close condition to BCM.
Key switch
Input key switch condition to BCM.
Remote keyless entry receiver
Receives lock/unlock signal from the keyfob, and then transmits to BCM.
Key switch
Input key switch ON/OFF condition to BCM.
Horn
Provides audible warning in panic mode.
COMPONENT PARTS
DLK-213
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
TRUNK LID OPENER SYSTEM : Component Parts Location
INFOID:0000000009756533
TRUNK LID OPENER SYSTEM : Component Description
INFOID:0000000009756534
1.
Trunk lid opener switch
2.
BCM (view with instrument panel re-
moved
3.
Trunk lid opener assembly (trunk lid
opener actuator and trunk room
lamp switch)
ALKIA2962ZZ
Item
Function
BCM
Controls the trunk lid opener system.
Trunk lid opener actuator
Releases the mechanical latch to open the trunk lid.
Trunk lid opener switch
Inputs the trunk open request to the BCM.
Trunk room lamp switch
Inputs the trunk lid open/close condition to the BCM.
DLK-214
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
SYSTEM (POWER DOOR LOCK SYSTEM)
SYSTEM (POWER DOOR LOCK SYSTEM)
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION : System Diagram
INFOID:0000000009756535
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION : System Description
INFOID:0000000009756536
DOOR LOCK FUNCTION
• The door lock and unlock switch (driver side) is built into power window main switch.
• The door lock and unlock switch (passenger side) is on door trim.
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors are
locked.
• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors are
unlocked.
Door Key Cylinder
• With the door key inserted in the door key cylinder on driver side, turning it to “LOCK”, will lock door lock
actuator of all doors.
• With the door key inserted in the door key cylinder on driver side, turning it to “UNLOCK” once unlocks the
driver side door lock actuator; turning it to “UNLOCK” again within 60 seconds after the first unlock operation
unlocks all of the other doors. - (SELECTIVE UNLOCK OPERATION)
Selective unlock operation mode can be changed using “DOOR LOCK-UNLOCK SET” mode in “WORK SUP-
PORT”. Refer to
BCS-87, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
AUTOMATIC DOOR LOCKS (LOCK OPERATION)
The automatic door locks function is the function that locks all doors linked with the vehicle speed or shift posi-
tion.
Vehicle Speed Sensing Auto Door Lock
*1
All doors are locked when the vehicle speed reaches 24 km/h (15 MPH) or more.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is turned ON, all
doors are closed and the vehicle speed received from the combination meter via CAN communication
becomes 24 km/h (15 MPH) or more.
ALKIA2288GB
Input
Single
Function
Actuator
Door lock/unlock switch
Door lock/unlock signal
Door lock function
• Each door lock actuator
Door key cylinder switch
Each door switch
Door open/close signal
Key reminder function
Combination meter.
Warning buzzer signal
Vehicle speed signal
Automatic door lock/unlock
function
SYSTEM (POWER DOOR LOCK SYSTEM)
DLK-215
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
If a door is opened and closed at any time during one ignition cycle (OFF
→ ON), even after initial auto door
lock operation has taken place, the BCM will relock all doors when the vehicle speed reaches 24 km/h (15
MPH) or more again.
Setting change of Automatic Door Locks (LOCK) Function
The LOCK operation setting of the automatic door locks function can be changed.
With CONSULT
The ON/OFF switching of the automatic door locks (LOCK) function and the type selection of the automatic
door locks (LOCK) function can be performed at the WORK SUPPORT setting of CONSULT. Refer to
"DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
Without CONSULT
The automatic door locks (LOCK) function can be switched ON/OFF by performing the following operation.
1. Close all doors (door switch OFF)
2. Push the ignition switch to the ON position
3. Press and hold the door lock and unlock switch for 5 seconds or more in the lock direction within 20 sec-
onds after turning the ignition switch ON.
4. The switching is completed when the hazard lamp blinks.
5. The ignition switch must be turned OFF and ON again between each setting change.
AUTOMATIC DOOR LOCKS (UNLOCK OPERATION)
The automatic door locks (UNLOCK) function is the function that unlocks all doors linked with the key position
or shift position.
IGN OFF Interlock Door Unlock
*1
All doors are unlocked when the power supply position is changed from ON to OFF.
BCM outputs the unlock signal to all door lock actuators when it detects that the power supply position is
changed from ignition switch ON to OFF.
Setting change of Automatic Door Locks (UNLOCK) Function
The UNLOCK operation setting of the automatic door locks function can be changed.
With CONSULT
The ON/OFF switching of the automatic door locks (UNLOCK) function and the type selection of the automatic
door locks (UNLOCK) function can be performed at the WORK SUPPORT setting of CONSULT. Refer to
87, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
Without CONSULT
The automatic door locks (UNLOCK) function can be switched ON/OFF by performing the following operation.
1. Close all doors (door switch OFF)
2. Place the ignition switch in the ON position
3. Press and hold the door lock and unlock switch for 5 seconds or more in the unlock direction within 20
seconds after turning the power supply position ON.
4. The switching is completed when the hazard lamp blinks.
5. The ignition switch must be turned OFF and ON again between each setting change.
*1
: This function is set to ON before delivery.
POWER DOOR LOCK SYSTEM
OFF
→ ON
: 2 blinks
ON
→ OFF
: 1 blink
OFF
→ ON
: 2 blinks
ON
→ OFF
: 1 blink
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст