Nissan Sentra. Manual — part 270
DLK-196
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
OUTSIDE KEY ANTENNA
OUTSIDE KEY ANTENNA
DRIVER SIDE
DRIVER SIDE : Removal and Installation
INFOID:0000000009756510
The driver side outside key antenna and driver side outside handle are serviced as an assembly. Refer to
DLK-173, "FRONT DOOR HANDLE : Removal and Installation - Outside Handle"
.
PASSENGER SIDE
PASSENGER SIDE : Removal and Installation
INFOID:0000000009756511
The passenger side outside key antenna and passenger side outside handle are serviced as an assembly.
DLK-173, "FRONT DOOR HANDLE : Removal and Installation - Outside Handle"
Installation is in the reverse order of removal.
REAR BUMPER
REAR BUMPER : Removal and Installation
INFOID:0000000009756513
REMOVAL
1. Remove rear bumper fascia. Refer to
EXT-20, "Removal and Installation"
2. Disconnect the harness connector (B) from the rear bumper key
antenna (1).
3. Remove the nuts (A) that retain the rear bumper key antenna (1)
to the body.
INSTALLATION
Installation is in the reverse order of removal.
ALKIA2723ZZ
DOOR REQUEST SWITCH
DLK-197
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR REQUEST SWITCH
DRIVER SIDE
DRIVER SIDE : Removal and Installation
INFOID:0000000009756514
The driver side door request switch and driver side outside handle are serviced as an assembly. Refer to
173, "FRONT DOOR HANDLE : Removal and Installation - Outside Handle"
PASSENGER SIDE
PASSENGER SIDE : Removal and Installation
INFOID:0000000009756515
The passenger side door request switch and passenger side outside handle are serviced as an assembly.
DLK-173, "FRONT DOOR HANDLE : Removal and Installation - Outside Handle"
TRUNK LID FINISHER
TRUNK LID FINISHER : Removal and Installation
INFOID:0000000009756516
REMOVAL
1. Remove the license lamp finisher. Refer to
EXT-44, "Removal and Installation"
.
2. Release the pawls and remove the trunk lid request switch (1).
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
ALKIA2722ZZ
DLK-198
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY WARNING BUZZER
INTELLIGENT KEY WARNING BUZZER
Removal and Installation
INFOID:0000000009756517
REMOVAL
NOTE:
The Intelligent Key warning buzzer is located in the front passenger side area of the engine compartment,
near the washer tank.
1. Remove the washer tank inlet. Refer to
.
2. Remove the nut (B) and the Intelligent Key warning buzzer (1).
3. Disconnect the harness connector (A) from the Intelligent Key
warning buzzer (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
ALKIA2933ZZ
REMOTE KEYLESS ENTRY RECEIVER
DLK-199
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY RECEIVER
Removal and Installation
INFOID:0000000009756518
REMOVAL
1. Remove glove box assembly. Refer to
IP-22, "Removal and Installation"
2. Disconnect the harness connector from the remote keyless entry receiver.
3. Remove the screw and remote keyless entry receiver.
INSTALLATION
Installation is in the reverse order or removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст