Nissan Sentra. Manual — part 329
EC-12
< PRECAUTION >
[MRA8DE]
PRECAUTIONS
• Do not depress accelerator pedal when starting.
• Immediately after starting, do not rev up engine unnecessar-
ily.
• Do not rev up engine just prior to shutdown.
• When installing C.B. ham radio or a mobile phone, be sure to
observe the following as it may adversely affect electronic
control systems depending on installation location.
- Keep the antenna as far as possible from the electronic con-
trol units.
- Keep the antenna feeder line more than 20 cm (8 in) away
from the harness of electronic controls.
Do not let them run parallel for a long distance.
- Adjust the antenna and feeder line so that the standing-wave
ratio can be kept smaller.
- Be sure to ground the radio to vehicle body.
SEF709Y
SEF708Y
PREPARATION
EC-13
< PREPARATION >
[MRA8DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009758324
NOTE:
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000009758325
Tool number
(Kent-Moore No.)
Tool name
Description
(J-44321)
Fuel pressure gauge
kit
Checks fuel pressure
(J-44321-6)
Fuel pressure adapter
Connects fuel pressure gauge to quick connector
type fuel lines
KV10120000
Fuel tube adapter
Measures fuel pressure
LEC642
LBIA0376E
JSBIA0410ZZ
Tool name
(Kent-Moore No.)
Description
(J-45488)
Quick connector re-
lease
Removes fuel tube quick connectors in engine
room
Leak detector
i.e.: (J-41416)
Locates the EVAP leak
PBIC0198E
S-NT703
EC-14
< PREPARATION >
[MRA8DE]
PREPARATION
EVAP service port
adapter
i.e.: (J-41413-OBD)
Applies positive pressure through EVAP service
port
Fuel filler cap adapter
i.e.: (MLR-8382)
Checks fuel tank vacuum relief valve opening
pressure
Socket wrench
Removes and installs engine coolant temperature
sensor
Oxygen sensor thread
cleaner
i.e.: (J-43897-18)
(J-43897-12)
Reconditions the exhaust system threads before
installing a new oxygen sensor. Use with anti-
seize lubricant shown below.
a: 18 mm diameter with pitch 1.5 mm for Zirco-
nia Oxygen Sensor
b: 12 mm diameter with pitch 1.25 mm for Tita-
nia Oxygen Sensor
Anti-seize lubricant
i.e.: (Permatex
TM
133AR or equivalent
meeting MIL specifica-
tion MIL-A-907)
Lubricates oxygen sensor thread cleaning tool
when reconditioning exhaust system threads.
Tool name
(Kent-Moore No.)
Description
S-NT704
S-NT815
S-NT705
AEM488
S-NT779
COMPONENT PARTS
EC-15
< SYSTEM DESCRIPTION >
[MRA8DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
SYSTEM DESCRIPTION
COMPONENT PARTS
ENGINE CONTROL SYSTEM
ENGINE CONTROL SYSTEM : Component Parts Location
INFOID:0000000009758326
ENGINE ROOM COMPARTMENT
No.
Component
Function
IPDM E/R
IPDM E/R control the internal relays and the actuators.
When CAN communication with ECM is impossible, IPDM
E/R performs fail-safe control.
With Intelligent Key System
•
PCS-7, "RELAY CONTROL SYSTEM : System Descrip-
tion"
•
•
PCS-8, "POWER CONSUMPTION CONTROL SYSTEM
: System Description"
Without Intelligent Key System
•
PCS-35, "RELAY CONTROL SYSTEM : System Descrip-
tion"
•
•
PCS-36, "POWER CONSUMPTION CONTROL SYS-
TEM : System Description"
Mass air flow sensor
(with intake air temperature sensor)
EC-28, "Mass Air Flow Sensor (with Intake Air Temperature
Sensor)"
Electric throttle control actuator
(with built in throttle position sensor and throttle control motor)
EC-22, "Electric Throttle Control Actuator"
ALBIA0980ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст