Nissan Sentra. Manual — part 880

TM-156

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

U0155 LOST COMMUNICATION (IPC)

U0155 LOST COMMUNICATION (IPC)

DTC Logic

INFOID:0000000009759390

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1. Start the engine and wait for at least 5 seconds.

2. Check the DTC.
Is “U0155” detected?

YES

>> Go to

TM-156, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009759391

For the diagnosis procedure, refer to

LAN-16, "Trouble Diagnosis Flow Chart"

.

DTC

CONSULT screen terms

[Trouble diagnosis content]

DTC detection condition

Possible causes

U0155

LOST COMM (IPC)
[Lost Communication With In-
strument Panel Cluster (IPC)
Control Module]

When the ignition switch is ON, TCM is unable
to receive the CAN communications signal
from the combination meter continuously for 2
seconds or more.

• Combination meter
• Harness or connector

(CAN communication line is open or
shorted)

U0300 CAN COMMUNICATION DATA

TM-157

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

U0300 CAN COMMUNICATION DATA

DTC Logic

INFOID:0000000009759392

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1. Start the engine and wait for 5 seconds or more.

2. Check the DTC.
Is “U0300” detected?

YES

>> Go to

TM-157, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009759393

1.

CONTROL UNIT CHECK

Check the number of control units replaced before “U0300” is detected.
Is one control unit replaced?

YES

>> The specification of the control unit replaced may be incorrect. Check the part number and the

specification.

NO

>> GO TO 2.

2.

CONTROL UNIT CHECK

With CONSULT

1. Remove one of the control unit replaced.

2. Assemble the old control unit before replacement.

3. Turn ignition switch ON, and wait for 2 seconds or more.

4. Select “Self Diagnostic Results” in “TRANSMISSION”.
Is “U0300”detected?

YES

>> Turn OFF the ignition switch and check other control units in the same manner.

NO

>> The specification of the control unit removed may be incorrect. Check the part number and the

specification.

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

U0300

CAN COMM DATA
(Internal Control Module Soft-
ware Incompatibility)

When the ignition switch is ON, the data length
transmitted from each control unit is shorter
than the specified length and the status contin-
ues for 2 seconds or more.

Control unit other than TCM

TM-158

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

U1000 CAN COMM CIRCUIT

U1000 CAN COMM CIRCUIT

Description

INFOID:0000000009759394

CAN (Controller Area Network) is a serial communication line for real-time application. It is an on-vehicle mul-

tiplex communication line with high data communication speed and excellent malfunction detection ability.

Many electronic control units are equipped onto a vehicle, and each control unit shares information and links

with other control units during operation (not independently). In CAN communication, control units are con-

nected with 2 communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission

with less wiring. Each control unit transmits/receives data but selectively reads required data only.

DTC Logic

INFOID:0000000009759395

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1. Start the engine and wait for at least 5 seconds.

2. Check the DTC.
Is “U1000” detected?

YES

>> Go to

TM-158, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009759396

For the diagnosis procedure, refer to

LAN-16, "Trouble Diagnosis Flow Chart"

.

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

U1000

CAN COMM CIRCUIT
(CAN Communication Line)

When the ignition switch is ON, TCM cannot
send the CAN communication signal continu-
ously for 2 seconds or more.

Harness or connector
(CAN communication line is open or
shorted)

U1117 LOST COMMUNICATION (ABS)

TM-159

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

U1117 LOST COMMUNICATION (ABS)

DTC Logic

INFOID:0000000009759397

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1. Start the engine and wait for 5 seconds or more.

2. Check the DTC.
Is “U1117” detected?

YES

>> Go to

TM-159, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009759398

For the diagnosis procedure, refer to

LAN-16, "Trouble Diagnosis Flow Chart"

.

DTC

CONSULT screen terms

[Trouble diagnosis content]

DTC detection condition

Possible causes

U1117

LOST COMM (ABS)
[Lost Communication With
ABS]

When the ignition switch is ON, TCM is unable
to receive the CAN communications signal
from ABS actuator and electric unit (control
unit) continuously for 2 seconds or more.

• ABS actuator and electric unit (control

unit)

• Harness or connector

(CAN communication line is open or
shorted)