Nissan Sentra. Manual — part 159
SYSTEM
BRC-23
< SYSTEM DESCRIPTION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• Brake force control function at braking hard detects driver
′s brake operations with the pressure sensor,
judges a brake booster
′s maximum brake power function by using information from the vacuum sensor, and
enhances more powerful braking force by controlling brakes of four wheels.
• VDC warning lamp blinks while VDC function is in operation and indicates to the driver that the function is in
operation.
• CONSULT can be used to diagnose the system.
• Fail-safe function is adopted. When a malfunction occurs in VDC function, the control is suspended for VDC
function and TCS function. However, ABS function and EBD function operate normally. Refer to
.
INPUT SIGNAL AND OUTPUT SIGNAL
Major signal transmission between each unit via communication lines is shown in the following table.
OPERATION CHARACTERISTICS
VDC Function That Prevents Oversteer Tendency
• During cornering, brake force (brake fluid pressure) is applied on front wheel and rear wheel on the outer
side of turn. Momentum is generated directing the vehicle toward the outer side of the turn. Oversteer is pre-
vented.
• Changing driving lane on a slippery road, when there may be a tendency to oversteer, engine output is con-
trolled as well as brake force (brake fluid pressure) of 4 wheels. Oversteer tendency decreases.
Component
Signal description
ECM
Transmits the following signals to ABS actuator and electric unit (control unit) via CAN commu-
nication.
• Acceleration pedal position signal
• Engine speed signal
• Target throttle position signal
TCM
Transmits the current gear position signal to ABS actuator and electric unit (control unit) via
CAN communication.
Steering angle sensor
Transmits the steering angle sensor signal to ABS actuator and electric unit (control unit) via
CAN communication.
Combination meter
Transmits the following signals to ABS actuator and electric unit (control unit) via CAN commu-
nication.
• Brake fluid level switch signal
• parking brake switch signal
Receives the following signals from ABS actuator and electric unit (control unit) via CAN com-
munication.
• VDC OFF indicator lamp signal
• SLIP indicator lamp signal
ALFIA0339GB
ALFIA0340GB
BRC-24
< SYSTEM DESCRIPTION >
[VDC/TCS/ABS]
SYSTEM
VDC Function That Prevents Understeer Tendency
• During cornering, brake force (brake fluid pressure) is applied on front wheel and rear wheel on the inner
side of turn. Momentum is generated directing the vehicle toward the inner side of the turn. Understeer is
prevented.
• Applying brakes during cornering on a slippery road, when there may be a tendency to understeer, engine
output is controlled as well as brake force (brake fluid pressure) of 4 wheels. Understeer tendency
decreases.
VDC/TCS/ABS : TCS Function
INFOID:0000000009757819
SYSTEM DIAGRAM
SYSTEM DESCRIPTION
JPFIC0137GB
ALFIA0341GB
AWFIA0807GB
SYSTEM
BRC-25
< SYSTEM DESCRIPTION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• Wheel spin status of drive wheel is detected by wheel sensor of 4
wheels. Engine output and transmission shift status is controlled
so that slip rate of drive wheels is in appropriate level. When wheel
spin occurs on drive wheel, ABS actuator and electric unit (control
unit) perform brake force control of LH and RH drive wheels (apply
brake force by increasing brake fluid pressure of drive wheel) and
decrease engine torque by engine torque control. Wheel spin
amount decreases. Engine torque is controlled to appropriate
level.
• TCS function can be switched to non-operational status (OFF) by
operating VDC OFF switch. In this case, VDC OFF indicator lamp
turns ON.
• SLIP indicator lamp blinks while TCS function is in operation and
indicates to the driver that the function is in operation.
• CONSULT can be used to diagnose the system.
• Fail-safe function is adopted. When a malfunction occurs in TCS
function, the control is suspended for VDC function and TCS func-
tion. However, ABS function and EBD function operate normally.
.
INPUT SIGNAL AND OUTPUT SIGNAL
Major signal transmission between each unit via communication lines is shown in the following table.
JPFIC0139GB
Component
Signal description
ECM
Transmits the following signals to ABS actuator and electric unit (control unit) via CAN commu-
nication.
• Accelerator pedal position signal
• Engine speed signal
• Target throttle position signal
TCM
Transmits the current gear position signal to ABS actuator and electric unit (control unit) via
CAN communication.
Steering angle sensor
Transmits the steering angle sensor signal to ABS actuator and electric unit (control unit) via
CAN communication.
Combination meter
Transmits the following signals to ABS actuator and electric unit (control unit) via CAN commu-
nication.
• Brake fluid level switch signal
• Parking brake switch signal
Receives the following signals from ABS actuator and electric unit (control unit) via CAN com-
munication.
• VDC OFF indicator lamp signal
• SLIP indicator lamp signal
BRC-26
< SYSTEM DESCRIPTION >
[VDC/TCS/ABS]
SYSTEM
VDC/TCS/ABS : ABS Function
INFOID:0000000009757820
SYSTEM DIAGRAM
• By preventing wheel lock through brake force (brake fluid pressure) control that is electronically controlled by
detecting wheel speed during braking, stability during emergency braking is improved so that obstacles can
be easily bypassed by steering operation.
• During braking, control units calculate wheel speeds, and transmit pressure increase, hold or decrease sig-
nals to actuator portion according to wheel slip status.
• The following effects are obtained by preventing wheel lock during
braking.
- Vehicle tail slip is prevented during braking when driving straight.
- Understeer and oversteer tendencies are moderated during brak-
ing while cornering.
- Obstacles may be easily bypassed by steering operation during
braking.
• CONSULT can be used to diagnose the system.
• Fail-safe function is adopted. When a malfunction occurs in ABS
function, the control is suspended for VDC function, TCS function
and ABS function. However, EBD function operates normally.
BRC-28, "VDC/TCS/ABS : Fail-safe"
INPUT SIGNAL AND OUTPUT SIGNAL
AWFIA0808GB
JPFIC0140GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст