Nissan Sentra. Manual — part 297
DLK-304
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
Exploded View
INFOID:0000000009756623
Removal and Installation
INFOID:0000000009756624
REMOVAL
CAUTION:
Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least three
minutes.
1. Disconnect the battery negative and positive terminals then wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
2. Remove crash zone sensor. Refer to
SR-25, "Removal and Installation"
.
3. Remove radiator. Refer to
CO-15, "Removal and Installation"
4. Remove the condenser (if equipped). Refer to
HA-39, "CONDENSER : Removal and Installation"
.
5. Remove the horns. Refer to
HRN-6, "Removal and Installation"
6. Remove air guides (LH/RH).
7. Remove the hood lock support bolts and hood lock support.
8. Remove the core support lower stay bolts and core support lower stay.
9. Remove the core support lower bolts and core support lower.
10. Remove the core support side member nuts and bolts and remove the core support side member, if nec-
essary.
INSTALLATION
1. Core support side member (RH)
2.
Core support upper
3.
Core support lower stay
4. Hood lock support
5.
Core support lower
6.
Core support side member (LH)
ALKIA2894ZZ
RADIATOR CORE SUPPORT
DLK-305
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Installation is in the reverse order of removal.
Tighten bolts to specification. Refer to
CAUTION:
After installation, perform hood fitting adjustment. Refer to
DLK-150, "HOOD ASSEMBLY : Adjust-
.
DLK-306
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT FENDER
FRONT FENDER
Exploded View
INFOID:0000000009756625
Removal and Installation
INFOID:0000000009756626
REMOVAL
1. Remove the front combination lamp. Ref to
EXL-119, "Removal and Installation"
.
2. Remove the front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
3. Remove the front fender protector. Refer to
EXT-28, "FENDER PROTECTOR : Removal and Installation -
.
4. Remove the front fender bolts and the front fender.
CAUTION:
Use shop cloths to protect the body from being damaged during removal and installation.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, perform fender adjustment procedure. Refer to
.
1.
Front fender
ALKIA2918ZZ
FRONT FENDER
DLK-307
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Adjustment
INFOID:0000000009756627
Check the clearance and the surface height between hood and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-
dures.
Unit: mm (in)
Adjustment
1. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
2. Remove the front fender protector. Refer to
EXT-28, "FENDER PROTECTOR : Removal and Installation -
.
1.
Front combination lamp assembly
2.
Fender
3.
Front bumper fascia
4.
Hood assembly
5.
Body side outer
6.
Front door
Section
Item
Measurement
Standard
A – A
F
Clearance
1.5 +1.2, -1.0 (0.06 + 0.05, -0.04)
G
Surface height
3.9
± 1.2 (0.15 ± 0.05)
B – B
H
Surface height
0.7
± 1.0 (0.03 ± 0.04)
J
Clearance
0.0
± 1.0 (0.00 ± 0.04)
C – C
K
Clearance
3.7
± 1.0 (0.15 ± 0.04)
M
Surface height
0.0
± 1.0 (0.00 ± 0.04)
D – D
N
Surface height
0.0
± 1.0 (0.00 ± 0.04)
O
Clearance
3.0
± 1.0 (0.12 ± 0.04)
E – E
P
Surface height
—
Q
Clearance
—
ALKIA3331ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст