Nissan Sentra. Manual — part 661
PB-10
< REMOVAL AND INSTALLATION >
PARKING BRAKE SHOE
3. Remove return springs (1) from the top of the parking brake
shoes.
4. Remove the return spring (1) from the lower side of the parking
brake shoes.
5. Remove springs (1) from the parking brake shoes.
CAUTION:
Do not drop the removed parts.
6. Remove parking brake shoes, adjuster, brake strut and toggle
lever.
CAUTION:
• The front parking brake shoes are made of different mate-
rials than the rear parking brake shoes. Install the parking
brake shoes in the proper location.
• Do not drop the removed parts.
7. Press the rear cable spring (1) against spring tension to remove
rear cable (3) from the clamp (A) of toggle lever (2).
CAUTION:
Do not bend rear cable.
8. Remove back plate (if necessary). Refer to
and Installation - Disc brake"
.
INSTALLATION
Installation is in the reverse order of removal.
• Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the back plate and brake shoe.
CAUTION:
The front parking brake shoes are made of different materials than the rear parking brake shoes.
Install the parking brake shoes in the proper location.
JSFIA1491ZZ
JSFIA1492ZZ
JSFIA1493ZZ
JSFIA0488ZZ
PARKING BRAKE SHOE
PB-11
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
• Assemble adjusters so that threaded part is expanded when rotat-
ing it in the direction shown by arrow.
• Shorten adjuster by rotating it.
• When disassembling apply PBC (Poly Butyl Cuprysil) grease or sil-
icone-based grease to threads.
• Check that the component parts of the parking brake shoe are
properly installed.
• Check parking brake shoe sliding surface and drum inner surface
for grease. Make sure that grease does not adhere to the friction
mating surfaces on the parking brake shoes and disc rotor.
Inspection and Adjustment
INFOID:0000000009757414
INSPECTION AFTER REMOVAL
Lining Thickness Inspection
• Check thickness (A) of lining.
Drum Inner Diameter Inspection
• Check inner diameter (B) of drum using suitable tool.
Other Inspections
Check the following items, and replace the parts if necessary.
• Lining for excessive wear, damage, and peeling.
• Brake shoe sliding surface for excessive wear and damage.
• Anti-rattle pin for excessive wear, damage and rust.
• Return spring and spring for settling, excessive wear, damage, and rust.
(A)
: For (RH) brake
(B)
: For (LH) brake
: Front
: Adjuster expands
JPFIB0087ZZ
JSFIA0489ZZ
Wear limit thickness
: Refer to
SBR021A
Wear limit of inner diameter
: Refer to
.
JPFIB0008ZZ
PB-12
< REMOVAL AND INSTALLATION >
PARKING BRAKE SHOE
• Adjuster for smoothness.
• Toggle lever and brake strut for excessive wear, damage and rust.
• Visually check inside of the drum for excessive wear, cracks, and damage.
ADJUSTMENT AFTER INSTALLATION
1. Adjust the parking brake lever stroke. Refer to
PB-4, "Inspection and Adjustment"
.
2. Rotate the disc rotor to check that there is no drag. Install the plug. If any drag is found, follow the proce-
dure described below.
a. Adjust parking brake stroke again.
b. Check rear disc brake.
3. Adjust the parking brake shoe. Refer to
SERVICE DATA AND SPECIFICATIONS (SDS)
PB-13
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Parking Drum Brake
INFOID:0000000009757415
Unit: mm (in)
Parking Brake Control
INFOID:0000000009757416
Brake lining
Wear limit thickness
1.5 (0.059)
Drum (in disc)
Wear limit of inner diameter
173 (6.81)
Item
Standard
Drum brake - number of notches [under force of 196 N (20.0 kg-f, 44.1 lb-f)]
8
− 9 notches
Disc brake - number of notches [under force of 196 N (20.0 kg-f, 44.1 lb-f)]
9
− 10 notches
Number of notches when brake warning lamp turns ON
1 notch
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст