Nissan Sentra. Manual — part 149
BR-38
< REMOVAL AND INSTALLATION >
FRONT DISC BRAKE
FRONT DISC BRAKE
BRAKE PAD
BRAKE PAD : Exploded View
INFOID:0000000009756015
BRAKE PAD : Removal and Installation
INFOID:0000000009756016
REMOVAL
WARNING:
Clean dust on brake caliper and brake pad with a vacuum dust collector to minimize the hazards of air-
borne particles or other material.
CAUTION:
• Do not depress the brake pedal while removing the brake pads because the pistons may pop out.
• It is not necessary to remove bolts on torque member and brake hose except for disassembly or
replacement of brake caliper. For brake pad removal, hang brake caliper with a wire so as not to
stretch brake hose.
• If brake fluid or grease adheres to the brake caliper or disc rotor, quickly wipe it off.
1. Partially drain brake fluid from the master cylinder. Refer to
.
2. Remove front wheels and tires using power tool. Refer to
WT-47, "Removal and Installation"
.
3. Remove sliding pin bolts.
4. Remove the brake caliper from the torque member. Leaving brake hose attached, reposition the brake
caliper aside with wire.
5. Remove the brake pads, shims, shim covers and pad retainers from the torque member.
CAUTION:
1.
Cylinder body
2.
Inner shim cover
3.
Inner shim
4.
Inner pad (with pad wear sensor)
5.
Pad retainer
6.
Torque member
7.
Outer pad
8.
Outer shim
9.
Outer shim cover
A.
Molykote AS880N
B.
Molykote 7439
AWFIA0976ZZ
FRONT DISC BRAKE
BR-39
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
• Do not deform the pad retainer (2) when removing the pad
retainer from the torque member (1).
• Do not damage the piston boot.
• Do not drop the brake pads, shims, and the shim covers.
• Note the position of components during removal to aid
with installation.
INSTALLATION
1. Install the pad retainers (1) to the torque member (2) if the pad
retainers have been removed.
CAUTION:
• Do not deform brake pad retainers.
• Verify pad retainers are secured properly to torque mem-
ber.
2. Apply Molykote AS880N or equivalent to the mating faces (A)
between the inner pad (1) and the inner shim (2), and install the
inner shim and inner shim cover (3) to the inner pad.
CAUTION:
Always replace the shim and shim cover when replacing
the brake pad.
3. Apply Molykote AS880N or silicone-based grease to the mating
faces (A) between the outer shim (1) and the outer shim cover
(2), and install the outer shim and outer shim cover to the outer
pad (3).
CAUTION:
Always replace the shim and shim cover when replacing
the brake pad.
JPFIA0118ZZ
PFIA0763J
JSFIA1336ZZ
JSFIA1330ZZ
BR-40
< REMOVAL AND INSTALLATION >
FRONT DISC BRAKE
4. Apply Molykote 7439 or equivalent to the mating faces (A)
between the brake pads (1) and the pad retainers.
5. Install the brake pads to the torque member.
CAUTION:
• Both inner and outer pads have a pad return system on
the pad retainer. Install pad return lever (1) securely to pad
retainer (2).
• Do not deform the pad retainers.
6. Using a suitable tool, press piston into the brake caliper.
CAUTION:
Do not damage the piston boot.
7. Install cylinder body to torque member.
8. Install the sliding pin bolts and tighten them to specified torque.
9. Depress the brake pedal several times to verify that drag does not exist.
10. Install front wheels and tires. Refer to
WT-47, "Removal and Installation"
.
BRAKE CALIPER ASSEMBLY
BRAKE CALIPER ASSEMBLY : Exploded View
INFOID:0000000009756017
JSFIA1337ZZ
JPFIA0027ZZ
1.
Brake caliper assembly
JPFIA0834GB
FRONT DISC BRAKE
BR-41
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
BRAKE CALIPER ASSEMBLY : Removal and Installation
INFOID:0000000009756018
REMOVAL
WARNING:
Clean dust on brake caliper and brake pad with a vacuum dust collector to minimize the hazard of air-
borne particles or other materials.
CAUTION:
• Do not depress the brake pedal.
• Do not spill or splash brake fluid on painted surfaces. Brake fluid may damage paint. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Do not bend, twist or pull the brake hoses and piping.
• Do not reuse drained brake fluid.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove front wheels and tires using power tool. Refer to
WT-47, "Removal and Installation"
.
2. Secure the disc rotor using wheel nuts.
3. Remove union bolt, copper sealing washers, and disconnect brake hose from brake caliper. Discard the
copper sealing washers.
CAUTION:
Do not reuse copper sealing washers.
4. Remove sliding pin bolts and the brake caliper.
CAUTION:
Do not drop brake pads or caliper.
INSTALLATION
1. Position the brake caliper to torque member and install the sliding pin bolts. Tighten to specification.
2. Assemble the union bolt (A) and the copper sealing washers (1)
to the brake hose and install it as an assembly to the brake cali-
per. Align the brake hose L-pin by aligning it with the brake cali-
per hole, and tighten the union bolt (A) to the specified torque.
CAUTION:
Do not reuse copper sealing washers.
3. Refill with new brake fluid and perform the air bleeding. Refer to
BR-17, "Bleeding Brake System"
CAUTION:
• Do not reuse drained brake fluid.
• Do not spill or splash brake fluid on the disc rotor.
4. Check the front disc brakes for drag. If drag exists, refer to
5. Install the front wheels and tires. Refer to
WT-47, "Removal and Installation"
.
AWFIA0795ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст