Nissan Sentra. Manual — part 499
FL-18
< DISASSEMBLY AND ASSEMBLY >
FUEL LEVEL SENSOR UNIT
2. Remove fuel tank temperature sensor (2) from fuel filter and fuel
pump assembly (1).
3. Using a suitable tool (2), remove fuel level sensor unit (3) from
fuel filter and fuel pump assembly (1).
CAUTION:
• Be careful not to damage the fuel level sensor unit.
• Do not disassemble fuel filter and fuel pump assembly.
ASSEMBLY
1. Check for damage of fuel level sensor unit installation position on the side of fuel filter and pump assem-
bly.
2. Slide fuel level sensor unit until it aligns to installation groove, then insert it until it stops.
• After inserting, apply force in reverse direction (removal direction) to ensure it cannot be pulled out.
3. Connect fuel level sensor unit/fuel tank temperature sensor harness connector.
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1. Turn ignition switch “ON” (with engine stopped), then check connections for leaks by applying fuel pres-
sure to fuel piping.
2. Start engine and let it idle and check there are no fuel leaks at the fuel system connections.
ALBIA0953ZZ
ALBIA0954ZZ
SERVICE DATA AND SPECIFICATIONS (SDS)
FL-19
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Fuel Tank
INFOID:0000000009756237
Standard and Limit
Unit: (US gal, lmp gal)
Fuel tank capacity
Approx. 50.0 (13-1/4, 11)
Fuel recommendation
Refer to
FSU-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
FSU
A
B
FSU
N
O
P
CONTENTS
FRONT SUSPENSION
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Procedure without Cowl Top Cover . ..
Precautions for Suspension . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
FRONT SUSPENSION ASSEMBLY . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
WHEEL ALIGNMENT . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . ..
Adjustment . . . . . . . . . . . . . . . ....
REMOVAL AND INSTALLATION . . . .
FRONT COIL SPRING AND STRUT . . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
TRANSVERSE LINK . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
FRONT STABILIZER . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
STEERING KNUCKLE . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
UNIT REMOVAL AND INSTALLATION . ..
FRONT SUSPENSION MEMBER . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY .
FRONT COIL SPRING AND STRUT . . . .
Exploded View . . . . . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
Disposal . . . . . . . . . . . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Alignment (Unladen*1) . . . . . . . . .
Ball Joint . . . . . . . . . . . . . . . . ..
FSU-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010289535
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000009758745
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precautions for Suspension
INFOID:0000000009758746
• When installing rubber bushings, the final tightening must be carried out under unladen conditions with tires
on ground. Spilled oil might shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
- Unladen conditions mean that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
• After servicing suspension parts, be sure to check wheel alignment.
• Self-lock nuts are not reusable. Always use new ones when installing. Since new self-lock nuts are pre-oiled,
tighten as they are.
• The tightening surface must be kept free from oil/grease.
• When jacking up the vehicle with a floor jack, do not hang the jack on the torque rod.
PIIB3706J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст