Nissan Sentra. Manual — part 240
DLK-76
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2622 INSIDE ANTENNA
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-73, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK INSIDE KEY ANTENNA CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and inside key antenna (console) connector.
3. Check continuity between BCM harness connector and inside key antenna (console) harness connector.
4. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 2
1. Replace inside key antenna (console). (New antenna or other antenna)
2. Connect BCM connector and inside key antenna (console) connector.
3. Turn ignition switch ON.
4. Check signal between BCM harness connector and ground using oscilloscope.
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M83
45
44
Ground
When Intelligent Key is in the anten-
na detection area
When Intelligent Key is not in the an-
tenna detection area
JMKIA3839GB
JMKIA5951GB
BCM
Inside key antenna (console)
Continuity
Connector
Terminal
Connector
Terminal
M83
45
M89
1
Yes
44
2
BCM
Ground
Continuity
Connector
Terminal
M83
45
No
44
B2622 INSIDE ANTENNA
DLK-77
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Replace inside key antenna (console).
NO
>> Replace BCM. Refer to
BCS-73, "Removal and Installation"
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M83
45
44
Ground
When Intelligent Key is in the anten-
na detection area
When Intelligent Key is not in the an-
tenna detection area
JMKIA3839GB
JMKIA5951GB
DLK-78
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2623 INSIDE ANTENNA
B2623 INSIDE ANTENNA
DTC Logic
INFOID:0000000009756377
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Check Intelligent Key relative signal strength
• Confirm vehicle Intelligent Key antenna signal strength
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Select INTELLIGENT KEY of BCM using CONSULT.
2. Select INSIDE ANT DIAGNOSIS in WORK SUPPORT mode.
3. Perform inside key antenna (INSIDE ANT DIAGNOSIS) on WORK SUPPORT of INTELLIGENT KEY.
4. Check BCM for DTC.
Is inside key antenna DTC detected?
YES
>> Refer to
.
NO
>> Inside key antenna (trunk room) is OK.
Diagnosis Procedure
INFOID:0000000009756378
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Check Intelligent Key relative signal strength
• Confirm vehicle Intelligent Key antenna signal strength
Regarding Wiring Diagram information, refer to
.
1.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch ON.
2. Check signal between BCM harness connector and ground using oscilloscope.
DTC
CONSULT display
description
DTC detecting condition
Possible cause
B2623
INSIDE ANTENNA 3
An excessive high or low voltage from inside anten-
na (trunk room) is sent to BCM
• Inside key antenna (trunk room)
• Harness between BCM and inside
key antenna (trunk room)
• BCM
B2623 INSIDE ANTENNA
DLK-79
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-73, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK INSIDE KEY ANTENNA CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and inside key antenna (trunk room) connector.
3. Check continuity between BCM harness connector and inside key antenna (trunk room) harness connec-
tor.
4. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 2
1. Replace inside key antenna (trunk room). (New antenna or other antenna)
2. Connect BCM connector and inside key antenna (trunk room) connector.
3. Turn ignition switch ON.
4. Check signal between BCM harness connector and ground using oscilloscope.
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M83
43
42
Ground
When Intelligent Key is in the anten-
na detection area
When Intelligent Key is not in the an-
tenna detection area
JMKIA3839GB
JMKIA5951GB
BCM
Inside key antenna (trunk room)
Continuity
Connector
Terminal
Connector
Terminal
M83
43
B49
1
Yes
42
2
BCM
Ground
Continuity
Connector
Terminal
M83
43
No
42
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст