Nissan Sentra. Manual — part 292
DLK-284
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB ID SET UP WITH CONSULT
KEYFOB ID SET UP WITH CONSULT
ID Code Entry Procedure
INFOID:0000000009756609
KEYFOB ID SET UP WITH CONSULT
NOTE:
• If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A spe-
cific ID code can be erased with CONSULT. However, when the ID code of a lost keyfob is not known,
all controller ID codes should be erased. After all ID codes are erased, the ID codes of all remaining
and/or new keyfobs must be re-registered.
• When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If
five ID codes are stored in memory when an additional code is registered, only the oldest code is
erased. If less than five codes are stored in memory when an additional code is registered, the new
ID code is added and no ID codes are erased.
• Entry of a maximum of five ID codes is allowed. When more than five codes are entered, the oldest ID
code will be erased.
• Even if the same ID code that is already in memory is input, the same ID code can be entered. The
code is counted as an additional code.
1. Turn ignition switch ON.
2. Select BCM.
3. Select MULTI REMOTE ENT.
4. Select WORK SUPPORT.
5. You can register, erase or confirm a keyfob ID code. To register a new code, select the following option
and follow CONSULT instructions:
• REMO CONT ID REGIST
Use this mode to register a keyfob ID code.
NOTE:
Register the ID code when keyfob or BCM is replaced, or when additional keyfob is required.
• REMO CONT ID ERASUR
Use this mode to erase a keyfob ID code.
• REMO CONT ID CONFIR
Use this mode to confirm if a keyfob ID code is registered or not.
KEYFOB ID SET UP WITHOUT CONSULT
DLK-285
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEYFOB ID SET UP WITHOUT CONSULT
ID Code Entry Procedure
INFOID:0000000009756610
KEYFOB ID SET UP WITHOUT CONSULT
NOTE:
• If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A specific ID
code can be erased with CONSULT. However, when the ID code of a lost keyfob is not known, all controller
ALKIA2029GB
DLK-286
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB ID SET UP WITHOUT CONSULT
ID codes should be erased. After all ID codes are erased, the ID codes of all remaining and/or new keyfobs
must be re-registered.
To erase all ID codes in memory, register one ID code (keyfob) five times. After all ID codes are erased, the
ID codes of all remaining and/or new keyfobs must be re-registered.
• When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If five ID
codes are stored in memory, when an additional code is registered, only the oldest code is erased. If less
than five ID codes are stored in memory, when an additional ID code is registered, the new ID code is added
and no ID codes are erased.
• If you need to activate more than two additional new keyfobs, repeat the procedure “Additional ID code
entry” for each new keyfob
DLK-284, "ID Code Entry Procedure"
(with CONSULT),
(without CONSULT).
• A maximum amount of five ID codes is allowed. When more than five ID codes are entered, the oldest ID
code will be erased.
• Even if same ID code that is already in the memory is input, the same ID code can be entered. The code is
counted as an additional code.
POWER DOOR LOCK SYSTEM SYMPTOMS
DLK-287
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SYMPTOM DIAGNOSIS
POWER DOOR LOCK SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000009756611
DOOR LOCK/UNLOCK FUNCTION MALFUNCTION
NOTE:
• Before performing the diagnosis in the following table, check “WORK FLOW”. Refer to
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
• If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
Symptom
Diagnosis/service procedure
Reference page
Key reminder door function does not operate
properly.
1.
Check door switch.
2.
Check key switch.
3.
Check Intermittent Incident.
Power door lock does not operate with door
lock and unlock switch on main power window
and door lock/unlock switch or power window
and door lock/unlock switch RH.
1.
Check BCM Power supply and ground circuit.
2.
Check main power window and door lock and unlock switch.
3.
Check power window and door lock and unlock switch RH.
4.
Check Intermittent Incident.
Specific door lock actuator does not operate.
1.
Check door lock actuator.
Driver side
Passenger side
Rear LH
Rear RH
2.
Check Intermittent Incident.
Power door locks do not operate with front
door lock key cylinder switch LH.
1.
Check key cylinder switch.
2.
Replace BCM.
Vehicle speed sensing auto door LOCK oper-
ation does not operate.
1.
Ensure automatic door lock/unlock function (lock operation)
is enabled.
2.
Check combination meter vehicle speed signal.
3.
Check intermittent incident.
Ignition OFF interlock auto door UNLOCK
function does not operate.
1.
Ensure automatic door lock/unlock function (unlock opera-
tion) is enabled.
2.
Check BCM for DTCs.
3.
Check intermittent incident.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст