Nissan Sentra. Manual — part 494
EXT-44
< REMOVAL AND INSTALLATION >
LICENSE LAMP FINISHER
LICENSE LAMP FINISHER
Exploded View
INFOID:0000000009758061
Removal and Installation
INFOID:0000000009758062
REMOVAL
1. Remove trunk lid finisher. Refer to
INT-45, "Removal and Installation"
2. Disconnect the harness connector (A) from trunk lid opener
request switch.
1.
Rear view camera
2.
Trunk lid opener request switch
3.
License lamp finisher
Clip
Pawl
AWKIA2124ZZ
JMKIB0246ZZ
LICENSE LAMP FINISHER
EXT-45
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
3. Remove license lamp finisher nuts (A).
4. Release clips of license lamp finisher from inside of trunk lid,
and then remove.
: Clip
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
When installing license lamp finisher, check that clips are placed in body panel holes, then press them
in.
JMKIB0247ZZ
AWKIA2125ZZ
E
X
T
- 4
6
< REMOVAL AND INSTALLATION >
REAR AIR SPOILER
REAR AIR SPOILER
Removal and Installation
INFOID:0000000009758063
Removal
1. Remove trunk lid finisher. Refer to
INT-45, "Removal and Installation"
2. Disconnect the harness connector from the high mounted stop lamp (if equipped).
3. Remove the rear air spoiler nuts.
4. Carefully release and lift the rear air spoiler from the gaskets using a suitable tool.
5. Carefully pry upward to release the foam tape (gasket) from trunk lid surface, using a suitable tool.
CAUTION:
Use care not to damage painted surfaces during removal or releasing of adhesive backed foam
tapes.
6. Release the high mounted stop lamp connector and grommet (if equipped) from trunk lid, then remove
rear air spoiler.
Installation
Installation is in the reverse order of removal.
NOTE:
• Before installing, be sure there are no gaps or waves in the foam tape (gasket) where the surfaces meet.
• During installation, be sure grommet of high mounted stop lamp harness is fully seated into trunk lid opening
prior to final rear air spoiler placement.
• Before installing rear air spoiler, clean the surface where it will be mounted with isopropyl alcohol or equiva-
lent to degrease the surface.
CAUTION:
Some plastic surfaces may become damaged if contacted by alcohol. Cover and protect the rear com-
bination lamp assemblies. If alcohol does come into contact with the lenses, immediately wash the
surface with water.
1.
Rear air spoiler
2.
High mounted stop lamp con-
nector (if equipped)
3.
Trunk lid
A. Grommet
B. Nut
Front
ALKIA2954ZZ
FL-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
FL
A
FL
N
O
P
CONTENTS
FUEL SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
General Precaution . . . . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
FUEL SYSTEM . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
Quick Connector . . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . .
FUEL LEVEL SENSOR UNIT, FUEL FILTER
AND FUEL PUMP ASSEMBLY . . . . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . .
FUEL TANK . . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
EVAP CANISTER . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . ..
FUEL LEVEL SENSOR UNIT . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст