Nissan Sentra. Manual — part 852
TM-44
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
23. Move 1st-2nd fork rod (1), fork rod (2), and reverse fork rod (3)
to the neutral position.
24. Install selector (4) to clutch housing.
CAUTION:
Replace selector lever and selector as a set.
25. Install selector spring (1) to return bushing (A).
26. Apply recommended sealant to the gasket surface of transaxle
case.
• Use Genuine Silicone RTV or an equivalent. Refer to
21, "Recommended Chemical Products and Sealants"
.
CAUTION:
• Do not allow old liquid gasket, moisture, oil, or foreign
matter to remain on gasket surface.
• Check that the gasket surface is not damaged.
• Apply sealant bead continuously.
27. Install transaxle case to clutch housing while rotating shifter
lever A (1) in the direction as shown.
28. Install reverse idler shaft bolt (
), as per the following proce-
dure.
a. Install sealing washer to reverse idler shaft bolt, and install
reverse idler shaft bolt to transaxle case.
CAUTION:
Do not reuse sealing washer.
b. Tighten reverse idler shaft bolt to the specified torque.
29. Tighten transaxle case bolts (
) to the specified torque.
SCIA7782E
JPDIC0445ZZ
JPDIC0110ZZ
PCIB1695E
PCIB1694E
TRANSAXLE ASSEMBLY
TM-45
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
30. Install position switch (1), with the following procedure.
a. Apply recommended sealant to threads of position switch.
• Use Genuine Silicone RTV or an equivalent.Refer to
"Recommended Chemical Products and Sealants"
CAUTION:
Do not allow old liquid gasket, moisture, oil, or foreign mat-
ter to remain on thread.
b. Install position switch to transaxle case and tighten it to the
specified torque.
31. Install bracket (2) to transaxle case and tighten bolt to the speci-
fied torque.
32. Install selector lever (3) with the following procedure.
a. Install selector lever to transaxle case.
CAUTION:
Replace selector lever and selector as a set.
b. Install retaining pin to selector lever using a suitable tool.
CAUTION:
Do not reuse retaining pin.
33. Install drain plug with the following procedure.
a. Install gasket to drain plug.
CAUTION:
Do not reuse gasket.
b. Install drain plug to clutch housing using a suitable tool.
c. Tighten drain plug to the specified torque.
CAUTION:
Do not overtighten drain plug as this could cause the transaxle case to crack.
34. Install filler plug with the following procedure.
a. Install gasket to filler plug and install it to the transaxle case.
CAUTION:
Do not reuse gasket.
b. Tighten filler plug to the specified torque.
CAUTION:
Fill with gear oil before tighten filler plug to the specified torque.
Do not overtighten the filler plug as this could cause the transaxle case to crack.
Inspection
INFOID:0000000009759290
INSPECTION AFTER DISASSEMBLY
SCIA7784E
TM-46
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
Check contact surface (
) and sliding surface (
) for excessive
wear, uneven wear, bend, and damage. Replace if necessary.
SCIA7785E
INPUT SHAFT AND GEAR
TM-47
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
INPUT SHAFT AND GEAR
Exploded View
INFOID:0000000009759291
Disassembly
INFOID:0000000009759292
CAUTION:
• Fix input shaft in a vise with back plate, and then remove gears and snap rings.
1.
Input shaft front bearing
2.
Input shaft
3.
3rd input gear
4.
Spacer
5.
Snap ring
6.
3rd baulk ring
7.
3rd-4th coupling sleeve
8.
3rd-4th synchronizer hub
9.
Insert key
10.
4th baulk ring
11.
4th input gear
12. 5th input gear
13.
5th baulk ring
14.
5th-6th coupling sleeve
15. 5th-6th synchronizer hub
16.
6th baulk ring
17.
Needle bearing
18. 6th input gear
19.
Input shaft rear bearing
A.
First step
B.
Final step
JPDIC0407GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст