Nissan Sentra. Manual — part 1
ACC-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
ACC
A
ACC
N
O
P
CONTENTS
ACCELERATOR CONTROL SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . .
ACCELERATOR CONTROL SYSTEM . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . ..
ACC-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010287580
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
ACCELERATOR CONTROL SYSTEM
ACC-3
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
ACC
N
P
O
REMOVAL AND INSTALLATION
ACCELERATOR CONTROL SYSTEM
Exploded View
INFOID:0000000009758117
Removal and Installation
INFOID:0000000009758118
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-21, "Removal and Installation"
2. Disconnect the harness connector From the accelerator pedal assembly.
3. Loosen bolts and remove accelerator pedal assembly.
CAUTION:
• Do not disassemble accelerator pedal assembly.
• Do not remove accelerator pedal position sensor from accelerator pedal assembly.
• Do not drop or impact the accelerator pedal assembly.
• Do not expose the accelerator pedal assembly to water.
INSTALLATION
Installation is in the reverse order of removal.
• Insert the locating hook and pin into the brake pedal bracket.
CAUTION:
Do not squeeze the locating hook into the brake pedal bracket when inserting the locating pin into the
hole on the brake pedal bracket side.
Inspection
INFOID:0000000009758119
INSPECTION AFTER INSTALLATION
1.
Accelerator pedal assembly
2.
Brake pedal bracket
A. Locating hook
B. Locating pin
JPBIA5259GB
ACC-4
< REMOVAL AND INSTALLATION >
ACCELERATOR CONTROL SYSTEM
• Check that the accelerator pedal moves smoothly within the speci-
fied range.
: Front
• For the electrical inspection of accelerator pedal position sensor. Refer to
CAUTION:
• Whenever the harness connector of accelerator pedal position sensor is disconnected, perform
“ACCELERATOR PEDAL RELEASED POSITION LEARNING”. Refer to
.
• The accelerator pedal should return smoothly to the fully raised position.
Accelerator pedal stroke (A) : Refer to
ALBIA0798ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст