Nissan Sentra. Manual — part 739
RSU-14
< REMOVAL AND INSTALLATION >
REAR SUSPENSION BEAM
9. Disconnect the brake hoses from the brake tubes on the rear suspension beam. Disconnect the brake
hoses and the brake tubes from the brackets. Refer to
BR-30, "REAR : Removal and Installation"
.
10. Remove the wheel hubs and bearings. Refer to
RAX-7, "Removal and Installation - Disc brake"
equipped) or to
RAX-6, "Removal and Installation - Drum brake"
(if equipped).
11. Set a suitable jack under the rear suspension beam.
CAUTION:
• At this step, the jack must be set only for supporting the removal procedure. For details on jack-
ing up the vehicle, refer to
GI-31, "Garage Jack and Safety Stand and 2-Pole Lift"
.
• Do not damage the rear suspension beam with the jack.
12. Remove the lower shock absorber bolts. Refer to
13. Slowly lower the suitable jack. Remove the upper rubber seats, the coil springs, and the lower rubber
seats from the rear suspension beam.
CAUTION:
Make sure the rear suspension beam is stable when using the jack.
14. Remove the rear suspension arm bracket bolts.
15. Slowly lower the suitable jack. Remove the rear suspension arm brackets and the rear suspension beam
from the vehicle.
16. Remove the rear suspension beam bolts and nuts.
17. Remove the rear suspension arm brackets from the rear suspension beam.
18. Inspect the components. Refer to
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse the rear suspension beam nuts.
• Perform the final tightening of the nuts and bolts under unladen conditions with the tires on level ground.
• Adjust the disc brake parking brake (if equipped). Refer to
PB-11, "Inspection and Adjustment"
• Adjust the drum brake parking brake (if equipped). Refer to
PB-4, "Inspection and Adjustment"
.
• Fill the hydraulic brake system. Refer to
• Bleed the hydraulic brake system. Refer to
BR-17, "Bleeding Brake System"
• Complete the inspection. Refer to
Inspection
INFOID:0000000009758789
INSPECTION AFTER REMOVAL
Check the rear suspension beam and the rear suspension beam brackets for deformation, cracks or damage.
Replace the parts if necessary.
INSPECTION AFTER INSTALLATION
1. Check the wheel sensor harness to be sure the connectors are fully seated.
2. Check the neutral position of the steering angle sensor. Refer to
3. Check the wheel alignment. Refer to
.
SERVICE DATA AND SPECIFICATIONS (SDS)
RSU-15
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment (Unladen*
1
)
INFOID:0000000009758790
*1: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
*2: Since an adjustment mechanism is not included, the value of the left and right wheels (both wheels) must be used as the standard
value.
Wheelarch Height (Unladen*)
INFOID:0000000009758791
UNITED STATES
Unit: mm (in)
*: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
CANADA
Camber
Degree minute (Decimal degree)
Minimum
−2° 00′ (−2.00°)
Nominal
−1° 30′ (−1.50°)
Maximum
−1° 00′ (−1.00°)
Total toe-in
Distance (A - B)
Nominal
In 3.5 mm (In 0.138 in)
Angle (LH and RH)
*2
Degree minute (Decimal degree)
Minimum
Out 0
° 03′ (Out 0.05°)
Nominal
In 0
° 20′ (In 0.33°)
Maximum
In 0
° 43′ (In 0.71°)
SFA234AC
Transaxle
6M/T or CVT
CVT
Tire size
205/55R16 (Except FE)
205/55R16 (FE)
205/50R17
Front (Hf)
703 (27.68)
706 (27.80)
708 (27.87)
Rear (Hr)
703 (27.68)
706 (27.80)
707 (27.83)
LEIA0085E
RSU-16
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Unit: mm (in)
*: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
Transaxle
6M/T or CVT
CVT
Tire size
205/55R16
205/50R17
Front (Hf)
704 (27.72)
709 (27.91)
Rear (Hr)
704 (27.72)
708 (27.87)
LEIA0085E
SB-1
RESTRAINTS
C
D
E
F
G
I
J
K
L
M
SECTION
SB
A
B
SB
N
O
P
CONTENTS
SEAT BELT
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Seat Belt Service . . . . . . . ...
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
BASIC INSPECTION . . . . . . . . .
COMPONENT INSPECTION . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
FRONT SEAT BELT . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
REAR SEAT BELT . . . . . . . . . . .
Exploded View - Seat Belt Retractor . . . . . ...
Removal and Installation - Seat Belt Retractor . .
Exploded View - Seat Belt Buckle . . . . . . ...
Removal and Installation - Seat Belt Buckle . . .
LATCH SYSTEM FOR CHILDREN . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
TOP TETHER STRAP CHILD RESTRAINT . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст