Nissan Sentra. Manual — part 623
LU-12
< REMOVAL AND INSTALLATION >
[MRA8DE]
OIL COOLER
REMOVAL AND INSTALLATION
OIL COOLER
Exploded View
INFOID:0000000009756259
M/T models
JSBIA2840ZZ
1.
Clamp
2.
Water hose
3.
Clamp
4.
Water hose
5.
Oil cooler
6.
O-rings
OIL COOLER
LU-13
< REMOVAL AND INSTALLATION >
[MRA8DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
CVT models
Removal and Installation
INFOID:0000000009756260
REMOVAL
1. Remove engine under cover. Refer to
.
2. Drain engine coolant. Refer to
CO-12, "Changing Engine Coolant"
CAUTION:
Perform when engine is cold.
3. Remove water hoses.
4. Remove bolts, oil cooler and O-rings.
CAUTION:
• Be careful not to get burned when engine and engine oil may be hot.
• When removing, prepare a shop cloth to absorb any engine oil leaks or spills.
• Completely wipe off any engine oil that adheres to engine and vehicle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse O-rings.
NOTE:
JSBIA2839ZZ
1.
Clamp
2.
Water hose
3.
Clamp
4.
Water hose
5.
Water hose clip
6.
Oil cooler
7.
Clamp
8.
Water hose
9.
O-rings
A.
To CVT oil warmer
LU-14
< REMOVAL AND INSTALLATION >
[MRA8DE]
OIL COOLER
Tighten the oil cooler bolts in order as shown to specification.
Inspection
INFOID:0000000009756261
INSPECTION AFTER REMOVAL
Oil Cooler
Check oil cooler for cracks. Check oil cooler for clogging by blowing through engine coolant inlet. If necessary,
replace oil cooler assembly.
INSPECTION AFTER INSTALLATION
1. Check the engine oil level and the engine coolant level and add engine oil and engine coolant. Refer to
2. Start the engine, and check that there are no leaks of engine oil or engine coolant.
3. Stop the engine and wait for 10 minutes.
4. Check the engine oil level and the engine coolant level again. Refer to
.
ALBIA0969ZZ
OIL PUMP
LU-15
< UNIT DISASSEMBLY AND ASSEMBLY >
[MRA8DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
UNIT DISASSEMBLY AND ASSEMBLY
OIL PUMP
INFOID:0000000009756262
Removal and Installation
INFOID:0000000009756263
REMOVAL
1. Remove engine under cover. Refer to
.
2. Remove air cleaner and air duct. Refer to
EM-25, "Removal and Installation"
1.
O-ring
2.
Oil pan (upper)
3.
Oil level gauge guide
4.
O-ring
5.
Oil level gauge
6.
Oil pump chain tensioner
7.
Oil pump drive chain
8.
Crankshaft sprocket
9.
Oil pump sprocket
10.
Oil pump
11.
Drain plug washer
12.
Drain plug
13.
Oil pan (lower)
14.
Oil filter
15.
Connector bolt
16.
Crankshaft position sensor
17.
Rear oil seal
A.
B.
Oil pan side
JSBIA2753GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст