Nissan Sentra. Manual — part 263
DLK-168
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
REAR DOOR
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000009756480
CAUTION:
• Use two people when removing or installing the rear door assembly due to its heavy weight.
• When removing and installing rear door assembly, support rear door with a suitable tool.
REMOVAL
1. Remove rear door assembly harness grommet (LH) (1) then pull
out door harness from body (2).
2. Disconnect the harness connector (A) from the door harness.
3. Remove the check link bolt from the body.
4. Remove rear door assembly hinge nuts (A) (door side) and the
door assembly (1).
JMKIA8083ZZ
JMKIA8084ZZ
ALKIA2710ZZ
REAR DOOR
DLK-169
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
Tighten rear door hinge nuts (door side) to specified torque.
CAUTION:
• After installation, check rear door open/close, lock/unlock operation.
• After installation, perform the rear door adjustment procedure. Refer to
.
DOOR ASSEMBLY : Adjustment
INFOID:0000000009756481
ADJUSTMENT
Check the clearance and surface height between rear door and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-
dure.
1. Front fender
2. Door assembly
3. Rear door assembly
4. Body side outer
5. Rear door striker
6. Rear door upper hinge
7. Rear door lower hinge
F. Rear door striker screws
AWKIA2887ZZ
DLK-170
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
Unit: mm (in)
LONGITUDINAL CLEARANCE
1. Remove the center pillar upper finisher. Refer to
INT-28, "CENTER PILLAR UPPER FINISHER : Removal
2. Loosen the rear door upper hinge nuts.
3. Loosen the rear door lower hinge bolts.
4. Move the rear door forward or backward as necessary until within specifications provided.
5. Tighten the lower hinge bolts to specification.
6. Tighten the upper hinge nuts to specification.
7. Install the center pillar upper finisher. Refer to
INT-28, "CENTER PILLAR UPPER FINISHER : Removal
SURFACE HEIGHT ADJUSTMENT
1. Loosen the rear door hinge nuts (door side) (A).
2. Move the top and/or the bottom of the rear door (1) in or out as
necessary until it is within specifications provided.
3. Tighten the rear door hinge nuts (door side) (A) to specification.
CAUTION:
• Check rear door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-pur-
pose grease.
• After adjusting, apply touch-up paint (body color) to the head of rear door assembly hinge bolts and
nuts.
Section
Item
Measurement
Standard
A – A
G
Clearance
4.0
± 1.0 (0.16 ± 0.04)
H
Surface height
0.0
± 1.0 (0.0 ± 0.04)
B – B
H
Clearance
4.2
± 1.0 (0.17 ± 0.04)
J
Surface height
0.0
± 1.0 (0.0 ± 0.04)
C – C
J
Clearance
4.0
± 1.0 (0.16 ± 0.04)
K
Surface height
0.0
± 1.0 (0.0 ± 0.04)
Rear door lower hinge bolts
22 N·m (2.2 kg-m, 16 ft-lb)
Rear door upper hinge nuts
22 N·m (2.2 kg-m, 16 ft-lb)
Rear door nuts
28.0 N·m (2.9 kg-m, 21 ft-lb)
ALKIA2710ZZ
REAR DOOR
DLK-171
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• If the clearance measurements cannot be corrected by adjusting the rear door, adjust the front door.
Refer to
DLK-164, "DOOR ASSEMBLY : Adjustment"
DOOR STRIKER ADJUSTMENT
Adjust rear door assembly striker so that it becomes parallel with door lock insertion direction.
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000009756482
CAUTION:
• Use two people when removing or installing rear door assembly due to its heavy weight.
• When removing and installing rear door assembly, support door using a suitable tool.
REMOVAL
1. Remove rear door assembly. Refer to
DLK-168, "DOOR ASSEMBLY : Removal and Installation"
2. Remove center pillar upper finisher (upper hinge only). Refer to
INT-28, "CENTER PILLAR UPPER FIN-
ISHER : Removal and Installation"
.
3. Remove rear door assembly upper hinge nuts (A) and remove.
4. Remove rear door assembly lower hinge bolts (A) and remove.
INSTALLATION
Installation is in the reverse order of removal.
Tighten rear door assembly hinge nuts and bolts to specified torque.Refer to
CAUTION:
• Apply anticorrosive agent onto the hinge mating surface.
• After installation, check rear door open/close, lock/unlock operation.
• After installation, perform the rear door adjustment procedure. Refer to
.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000009756483
REMOVAL
ALKIA2711ZZ
ALKIA2712ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст