Nissan Sentra. Manual — part 321
DMS-56
< DTC/CIRCUIT DIAGNOSIS >
[SPORT MODE (M/T)]
SPORT MODE SWITCH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace SPORT mode switch. Refer to
DMS-58, "Removal and Installation"
SPORT mode
switch
Condition
Continuity
Terminal
6 – 8
SPORT mode switch is de-
pressed.
Existed
SPORT mode switch is released.
Not existed
DMS
SPORT MODE
DMS-57
< DTC/CIRCUIT DIAGNOSIS >
[SPORT MODE (M/T)]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
SPORT MODE
Component Function Check
INFOID:0000000009755932
1.
CHECK SPORT MODE OPERATION
1. Turn ignition switch ON.
2. Check SPORT mode indicator lamp turns ON/OFF on combination meter when turn SPORT mode switch
ON/OFF.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Proceed to
Diagnosis Procedure
INFOID:0000000009755933
1.
CHECK DTC IN ECM
With CONSULT
Check “Self Diagnostic Results” in “ENGINE”.
Are any DTC detected?
YES
>> Check DTC detected item. Refer to
NO
>> GO TO 2.
2.
CHECK DTC IN COMBINATION METER
With CONSULT
Check “Self Diagnostic Results” in “METER/M&A”.
Is any DTC detected?
YES
>> Check DTC detected item. Refer to
NO
>> GO TO 3.
3.
CHECK COMBINATION METER
With CONSULT
1. Select “Data Monitor” in “METER/M&A”.
2. Check that “SPORT MODE IND” turns ON/OFF when SPORT mode switch is operated. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-77, "Removal and Installation"
NO
>> GO TO 4.
4.
CHECK SPORT MODE SWITCH SYSTEM
Check SPORT mode switch system. Refer to
DMS-53, "Component Function Check"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace error-detected parts.
DMS-58
< REMOVAL AND INSTALLATION >
[SPORT MODE (M/T)]
SPORT MODE SWITCH
REMOVAL AND INSTALLATION
SPORT MODE SWITCH
Removal and Installation
INFOID:0000000009755934
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-21, "Removal and Installation"
.
2. Remove SPORT mode switch.
INSTALLATION
Installation is in the reverse order of removal.
DMS
PRECAUTIONS
DMS-59
< PRECAUTION >
[SPORT MODE (CVT)]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010291076
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст