Nissan Sentra. Manual — part 487
EXT-16
< REMOVAL AND INSTALLATION >
FRONT BUMPER
REMOVAL AND INSTALLATION
FRONT BUMPER
Exploded View
INFOID:0000000009758032
1.
Grommet
2.
Front bumper side bracket (RH)
3.
Front under cover
4.
Front air spoiler
5.
Front bumper reinforcement
6.
Front energy absorber
7.
Front fog lamp (RH) (if equipped)
8.
Front bumper lower grille
9.
Front bumper fascia finisher (RH)
(if equipped)
AWKIA2104ZZ
FRONT BUMPER
EXT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000009758033
CAUTION:
Bumper fascia is made of resin. Use care when handling to prevent damage. Avoid contact with oily
substances.
REMOVAL
1. Remove front grille. Refer to
EXT-23, "Removal and Installation"
2. Remove front bumper fascia clips (A) from front bumper fascia
upper side.
3. Remove front bumper fascia clips (A) from front bumper fascia
lower side.
4. Remove fender protector bolts (A) (LH/RH).
10. Front fog lamp finisher (RH) (if
equipped)
11. License plate bracket
12. Tow cover
13. Front fog lamp finisher (LH) (if
equipped)
14. Front bumper fascia finisher (LH)
(if equipped)
15. Front bumper fascia
16. Front fog lamp (LH) (if equipped)
17. Grommet
18. Front bumper side bracket (LH)
Pawl
JMKIA8445ZZ
AWKIA2105ZZ
JMKIA8446ZZ
EXT-18
< REMOVAL AND INSTALLATION >
FRONT BUMPER
5. Remove front bumper fascia screws (A) (LH/RH).
6. Apply protective tape (A) to protect the component from damage
on each side as shown.
7. Release the front bumper fascia to release from the front
bumper fascia side bracket on each side (LH/RH) as shown.
: Pawl
CAUTION:
When removing front bumper fascia two people are required to
avoid damaging.
8. Disconnect the harness connectors from the front fog lamps (if equipped).
9. Remove the front bumper fascia.
10. Release front fog lamp finisher pawls, then remove front fog
lamp finishers (LH/RH).
: Pawl
11. Remove the front fog lamp assemblies (LH/RH) (if equipped) from front bumper fascia. Refer to
12. Remove front bumper energy absorber.
13. Remove front bumper reinforcement nuts and the front bumper reinforcement.
14. Remove front bumper side bracket screws and the front bumper side brackets (LH/RH).
15. Remove front under cover bolts, clips and front under cover.
INSTALLATION
JMKIA8449ZZ
JMKIB0220ZZ
AWKIA2107ZZ
AWKIA2108ZZ
FRONT BUMPER
EXT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Installation is in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation status.
• Fitting adjustment cannot be performed.
JMKIA8589ZZ
Portion Clearance
Surface
height
difference
Front bumper fascia– Front grille
A-A
0.4 – 2.8 mm
(0.02 – 0.11 in)
0.0 – 3.4 mm
(0.00 – 0.13 in)
Front bumper fascia – Hood
B-B
4.0 – 8.4 mm
(0.16 – 0.33 in)
—
Front bumper fascia – Front combina-
tion lamp
C-C
0.5 – 2.9 mm
(0.02 – 0.11 in)
—
D-D
1.5 – 3.9 mm
(0.06 – 0.15 in)
—
Front bumper fascia – Front fender
E-E
0.0 – 1.0 mm
(0.00 –0.04 in)
(
−0.3) – (+1.7) mm
[(
−0.01) – (+0.07) in]
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст