Nissan Sentra. Manual — part 900
TM-236
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
OVERDRIVE CONTROL SWITCH
OVERDRIVE CONTROL SWITCH
Component Function Check
INFOID:0000000009759483
1.
CHECK SPORT INDICATOR LAMP FUNCTION
Check OD OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Go to
2.
CHECK SPORT MODE SWITCH FUNCTION
1. Shift the selector lever to “D” position.
2. Check that OD OFF indicator lamp turns ON/OFF when overdrive control switch is operated.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000009759484
1.
CHECK OVERDRIVE CONTROL SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector connector.
3. Turn ignition switch ON.
4. Check voltage between CVT shift selector harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK CVT SHIFT SELECTOR ASSEMBLY
Check continuity between CVT shift selector connector terminals.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
NO
>> GO TO 3.
3.
CHECK OVERDRIVE CONTROL SWITCH
Check overdrive control switch. Refer to
TM-237, "Component Inspection (Overdrive Control Switch)"
Is the inspection result normal?
YES
>> Replace CVT shift selector assembly. Refer to
TM-253, "Removal and Installation"
.
NO
>> Repair or replace malfunctioning parts.
4.
CHECK GROUND CIRCUIT
Check continuity between CVT shift selector harness connector terminal and ground.
CVT shift selector
Voltage
(Approx.)
Connector
+
-
Terminal
M38
1
2
5 V
CVT shift selector
Condition
Continuity
Terminal
1 – 2
Overdrive control switch is depressed.
Existed
Overdrive control switch is released.
Not existed
OVERDRIVE CONTROL SWITCH
TM-237
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CHECK CIRCUIT BETWEEN COMBINATION METER AND CVT SHIFT SELECTOR (PART 1)
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector terminal and CVT shift selector harness
connector terminal.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning parts.
6.
CHECK CIRCUIT BETWEEN COMBINATION METER AND CVT SHIFT SELECTOR (PART 2)
Check continuity between combination meter harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace malfunctioning parts.
7.
CHECK COMBINATION METER INPUT SIGNAL
1. Connect all of disconnected connectors.
2. Turn ignition switch ON.
3. Select “Data Monitor” in “METER/M&A”.
4. Select “O/D OFF SW”.
5. Check that “O/D OFF SW” turns ON/OFF when overdrive control switch is operated. Refer to
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
NO
>> Replace combination meter. Refer to
MWI-77, "Removal and Installation"
Component Inspection (Overdrive Control Switch)
INFOID:0000000009759485
1.
CHECK OVERDRIVE CONTROL SWITCH
CVT shift selector
—
Continuity
Connector
Terminal
M38
2
Ground
Existed
Combination meter
CVT shift selector
Continuity
Connector
Terminal
Connector
Terminal
M24
8
M38
1
Existed
Combination meter
—
Continuity
Connector
Terminal
M24
8
Ground
Not existed
TM-238
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
OVERDRIVE CONTROL SWITCH
Check continuity between wires of selector lever knob .
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace selector lever knob. Refer to
.
Condition
Continuity
Overdrive control switch is depressed
Existed
Overdrive control switch is released
Not existed
JSDIA2795ZZ
OD OFF INDICATOR LAMP
TM-239
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OD OFF INDICATOR LAMP
Component Function Check
INFOID:0000000009759486
1.
CHECK OD OFF INDICATOR LAMP FUNCTION
Check OD OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000009759487
1.
CHECK DTC (TCM)
With CONSULT
1. Turn ignition switch ON.
2. Check “Self Diagnostic Results” in “TRANSMISSION”.
Is any DTC detected?
YES
>> Check DTC detected item. Refer to
NO
>> GO TO 2.
2.
CHECK DTC (COMBINATION METER)
With CONSULT
Check “Self Diagnostic Results” in “METER/M&A”.
Is any DTC detected?
YES
>> Check DTC detected item. Refer to
NO
>> GO TO 3.
3.
CHECK COMBINATION METER INPUT SIGNAL
With CONSULT
1. Shift the selector lever to “D” position.
2. Select “Data Monitor” in “METER/M&A”.
3. Select “O/D OFF IND”.
4. Check that “O/D OFF IND” turns ON/OFF when overdrive control switch is operated. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-77, "Removal and Installation"
NO
>> GO TO 4.
4.
CHECK TCM INPUT/OUTPUT SIGNAL
With CONSULT
1. Select “Data Monitor” in “TRANSMISSION”.
2. Select “SPORT MODE SW”.
3. Check that “SPORT MODE SW” turns ON/OFF when overdrive control switch is operated. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-77, "Removal and Installation"
NO
>> Check overdrive control switch circuit. Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст