Nissan Sentra. Manual — part 611
REAR PARCEL SHELF FINISHER
INT-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Removal and Installation
INFOID:0000000009756917
REMOVAL
1. Remove high-mounted stop lamp (if equipped). Refer to
EXL-124, "Removal and Installation"
.
2. Remove rear pillar finisher (LH/RH). Refer to
INT-29, "REAR PILLAR FINISHER : Removal and Installa-
3. Remove top three clips from the rear seatback finishers (LH/RH).
4. Remove the rear seat belt lower anchor bolts. Refer to
SB-11, "Removal and Installation - Seat Belt
.
5. Remove rear parcel shelf finisher.
a. Release seat belt finisher pawls using a suitable tool (A) and
remove all seat belt finishers (LH/RH/center).
: Pawl
b. Route all rear seat belts through rear parcel shelf finisher.
c. Release the rear parcel shelf finisher clips as shown.
: Clip
d. Pull rear parcel shelf finisher forward and remove.
6. Remove top tether strap anchor finishers from rear parcel shelf finisher.
INSTALLATION
Installation is in the reverse order of removal.
7.
Top tether strap anchor finisher
(LH)
8.
Seat belt finisher (LH)
9.
Seat belt finisher (center)
10.
High-mounted stop lamp
Pawl
Clip
AWJIA0977ZZ
AWJIA0975ZZ
JMJIA7802ZZ
INT-34
< REMOVAL AND INSTALLATION >
REAR PARCEL SHELF FINISHER
Removal and Installation-Top Tether Strap Anchor Finisher
INFOID:0000000009756918
REMOVAL
Release top tether strap anchor finisher pawls and remove the top tether strap anchor finisher.
INSTALLATION
Installation is in the reverse order of removal.
FLOOR TRIM
INT-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
FLOOR TRIM
Exploded View
INFOID:0000000009756919
Removal and Installation
INFOID:0000000009756920
REMOVAL
1. Remove front seat assemblies. Refer to the following.
SE-18, "DRIVER SIDE : Removal and Installation - Seat Assembly"
(Driver Seat).
• Refer to
SE-20, "PASSENGER SIDE : Removal and Installation - Seat Assembly"
(Passenger Seat).
2. Remove rear seat cushion assembly. Refer to
SE-23, "Removal and Installation - Seat Cushion Assem-
3. Remove dash side finishers (LH/RH). Refer to
INT-26, "DASH SIDE FINISHER : Removal and Installa-
4. Remove center pillar lower finishers (LH/RH). Refer to
INT-27, "CENTER PILLAR LOWER FINISHER :
.
ALJIA1130ZZ
1.
Floor trim
2.
Harness protector
3.
Front floor spacer (RH)
4.
Front floor spacer (LH)
5.
Rear floor spacer (LH)
6.
Rear floor spacer (RH)
7.
Column hole cover
Pawl
Front
INT-36
< REMOVAL AND INSTALLATION >
FLOOR TRIM
5. Remove rear pillar lower finishers (LH/RH). Refer to
INT-30, "REAR PILLAR FINISHER : Removal and
Installation - Rear Pillar Lower Finisher"
6. Remove lap pre-tensioner anchor bolt. Refer to
SB-8, "Removal and Installation"
.
7. Remove center console assembly. Refer to
IP-17, "Removal and Installation"
8. Remove console rear bracket. Refer to
9. Remove rear floor duct. Refer to
VTL-7, "REAR FLOOR DUCT : Removal and Installation - Rear Floor
10. Remove shift selector assembly. Refer to
TM-253, "Removal and Installation"
11. Remove diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
.
12. Remove parking brake lever assembly. Refer to
PB-7, "Removal and Installation"
.
13. Remove nut (A) and then remove instrument stay.
14. Disconnect drain hose.
15. Remove clips (A) and the column hole cover.
16. Release pawl using a suitable tool (A) and open the harness
protector.
: Pawl
JMIIA1942ZZ
JMIIA1950ZZ
JMJIA6499ZZ
ALJIA1131ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст