Nissan GT-R. Manual — part 130
WHEEL ALIGNMENT
FSU-9
< PERIODIC MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
• Refer to figure for selection of shim.
• Assemble the shims and the rubber bushings while facing the rubber bushings toward the upper
link side.
NOTE:
The shims and rubber bushings are fitted on a new vehicle [shim: 3 mm (0.12 in)] are a single unit. However
the shims for adjustment and rubber bushings are separated parts. When shim: 6 mm (0.24in) is selected, fix
it on one side only.
JPEIA0116GB
FSU-10
< REMOVAL AND INSTALLATION >
FRONT COIL SPRING AND SHOCK ABSORBER
REMOVAL AND INSTALLATION
FRONT COIL SPRING AND SHOCK ABSORBER
Exploded View
INFOID:0000000009163821
Disposal
INFOID:0000000009163825
1.
Set shock absorber horizontally with the piston rod fully extended.
2.
Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position (
) from top
as shown in the figure to release gas gradually.
CAUTION:
• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in this direction (
).
• Directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.
3.
Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
1.
Cap
2.
Piston rod lock nut
3.
Vehicle body
4.
Mounting seal
5.
Mount insulator
6.
Rubber seat
7.
Bound bumper
8.
Coil spring*
9.
Shock absorber
*: To replace, all of four coil springs must be replaced together as a set. (Vehicles with track pack-specific suspension)
Refer to
for the symbols in the figure.
JPEIA0117GB
A
: 20 – 30 mm (0.79 – 1.18 in)
NNEIA0021ZZ
TRANSVERSE LINK
FSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
TRANSVERSE LINK
Exploded View
INFOID:0000000009163826
*: The shims and rubber bushings are fitted on a new vehicle [shim: 3 mm (0.12 in)] are a single unit. However the shims for adjustment
and rubber bushings are separated parts. When shim: 6 mm (0.24in) is selected, fix it on one side only.
1.
Shim*
2.
Rubber bushing
3.
Upper link
4.
Transverse link
5.
Adjusting bolt
6.
Eccentric disk
Refer to
for the symbols in the figure.
JSEIA0366GB
FSU-12
< REMOVAL AND INSTALLATION >
UPPER LINK
UPPER LINK
Exploded View
INFOID:0000000009163829
*: The shims and rubber bushings are fitted on a new vehicle [shim: 3 mm (0.12 in)] are a single unit. However the shims for adjustment
and rubber bushings are separated parts. When shim: 6 mm (0.24in) is selected, fix it on one side only.
1.
Shim*
2.
Rubber bushing
3.
Upper link
4.
Transverse link
5.
Adjusting bolt
6.
Eccentric disk
for the symbols in the figure.
JSEIA0366GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст