Nissan GT-R. Manual — part 122
EXT-42
< REMOVAL AND INSTALLATION >
FLOOR SIDE FAIRING
Installation position for clip
NNKIA0108GB
1.
Rear wheel well protector LH
2.
Rear diffuser assembly
3.
Rear bumper fascia (lower)
: Vehicle front
FLOOR SIDE FAIRING
EXT-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Bracket construction
REAR DIFFUSER : Removal and Installation
INFOID:0000000009161574
CAUTION:
• Never apply any chemical products like wax, coating agent, and compound for carbon parts. They
are produced by composite manufacturing methods similar to a racing vehicle and special paint is
adopted to enhance the look and feel of materials. (Otherwise, water may penetrate to carbon layers
and may cause corrosion.)
• Never place any carbon parts directly on the ground. Always protect them using a soft sheet during
removal, installation, and replacement operations.Never touch carbon parts with oily hands or allow
oil or grease to get on them.
REMOVAL
Rear diffuser (center)
1.
Remove the clips connecting with the rear bumper fascia (lower) lower surface.
2.
Remove the rear diffuser (center) mounting bolts.
3.
Remove the rear diffuser (center).
NNKIA0106GB
1.
Rear panel assembly
2.
Diffuser bracket A LH
3.
Diffuser bracket A RH
4.
Diffuser center bracket
5.
Diffuser bracket B RH
6.
Diffuser bracket B LH
7.
Diffuser bracket C RH
8.
Diffuser bracket C LH
Refer to
for symbols in the figure.
EXT-44
< REMOVAL AND INSTALLATION >
FLOOR SIDE FAIRING
Rear diffuser RH
1.
Remove the rear diffuser (center).
2.
Remove the mounting bolts and clips of rear diffuser RH.
3.
Remove the rear diffuser RH.
Rear diffuser LH
1.
Remove the rear diffuser (center).
2.
Remove the mounting bolts and clips of rear diffuser LH.
3.
Remove the rear diffuser LH.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• When rear diffuser mounting bolt is removed, check for surface treatment peel off and oxidation of
mounting bolt and washer so that electric corrosion is prevented.
• Regarding mounting bolt and washer with surface treatment peel off, paint contact surface of washer
and carbon using touch pen or others. By doing so, mounting bolt and washer are reusable. How-
ever, regarding oxidation, never reuse.
• Visually check the clips for deformation and damage at installation. Replace with new ones if neces-
sary.
• Always tighten the mounting bolts to the specified torque.
ROOF SIDE MOLDING
EXT-45
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
ROOF SIDE MOLDING
Exploded View
INFOID:0000000009161575
Removal and Installation
INFOID:0000000009161576
REMOVAL
Disengage the joint of clips from the roof side molding (1) rear edge
with the remover tool (A).
CAUTION:
Wrap a shop cloth (B) around the remover tool to protect the
body panel from damage.
INSTALLATION
Install in the reveres order of removal.
REMOVAL AND INSTALLATION OF ROOF SIDE MOLDING CLIP
Removal
1.
Remove roof side molding.
1.
Roof side molding
2.
Roof side molding clip
3.
Roof panel
4.
Front pillar finisher
NNKIA0149ZZ
: Clip
JMKIA1246ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст