Nissan GT-R. Manual — part 333
WW-24
< REMOVAL AND INSTALLATION >
WIPER BLADE
3.
Insert the wiper refill until the stopper at the rear end of wiper
refill fits in the tab. Check that “LOCK” mark on wiper refill is
aligned with “ ” mark on wiper blade.
4.
Untwist the twisted wiper refill (
) at the rear end of wiper
blade, if any.
5.
Check the following items after replacing wiper refill.
• Wiper refill is not twisted at all.
• Wiper refill thoroughly fits in the tab on wiper blade.
• Wiper refill is inserted from the proper direction.
NOTE:
When the vertebra is detached.
• Insert the vertebra (1) into the wiper blade to the same bending
direction.
• If a vertebra has a notch, fit it to a protrusion inside the wiper refill.
NOTE:
For the passenger side wiper blade there are two length types. They
can be identified by the arrow as shown in the figure.
JPLIA1585ZZ
JPLIA1586ZZ
Red paint mark
Without paint mark
475 mm (18.70 in)
525 mm (20.67 in)
JMLIA3779ZZ
FRONT WIPER DRIVE ASSEMBLY
WW-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER DRIVE ASSEMBLY
Exploded View
INFOID:0000000009161880
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000009161881
REMOVAL
1.
Remove the front wiper arm. Refer to
.
2.
Remove the cowl top cover. Refer to
EXT-27, "Removal and Installation"
.
3.
Remove the font wiper drive assembly mounting bolts.
1.
Front wiper drive assembly
JPLIA1179ZZ
1.
Front wiper linkage 1
2.
Shaft seal
3.
Front wiper frame
4.
Front wiper motor
5.
Front wiper linkage 2
: Multi
−
purpose grease or an equivalent.
JPLIA1180ZZ
WW-26
< REMOVAL AND INSTALLATION >
FRONT WIPER DRIVE ASSEMBLY
4.
Disconnect the front wiper motor connector.
5.
Remove the front wiper drive assembly from the vehicle.
INSTALLATION
1.
Install the front wiper drive assembly to the vehicle.
2.
Connect the front wiper motor connector.
3.
Operate the front wiper to move it to the auto stop position.
4.
Install the cowl top cover. Refer to
EXT-27, "Removal and Installation"
5.
Install the front wiper arms. Refer to
.
Disassembly and Assembly
INFOID:0000000009161882
DISASSEMBLY
1.
Remove the front wiper linkage 1 and 2 from the front wiper drive assembly.
CAUTION:
Never bend the linkage or damage the plastic part of the ball joint when removing the wiper link-
age.
2.
Remove the front wiper motor mounting screws, and then remove the front wiper motor from the front
wiper frame.
ASSEMBLY
1.
Connect the front wiper motor connector.
2.
Operate the front wiper to move it to the auto stop position.
3.
Disconnect the front wiper motor connector.
4.
Install the front wiper motor to the front wiper frame.
5.
Install the front wiper linkage 2 to the front wiper motor and the front wiper frame.
6.
Install the front wiper linkage 1 to the front wiper frame.
CAUTION:
• Never drop front wiper motor or cause it to come into contact with other parts.
• Be careful for the grease condition at the front wiper motor and front wiper linkage joint
(retainer). Apply Multi
−
purpose grease or an equivalent if necessary.
WIPER AND WASHER SWITCH
WW-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WIPER AND WASHER SWITCH
Exploded View
INFOID:0000000009161883
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст