Nissan GT-R. Manual — part 115
EXT-14
< REMOVAL AND INSTALLATION >
FRONT BUMPER
REMOVAL AND INSTALLATION
FRONT BUMPER
Exploded View
INFOID:0000000009161553
NNKIA1739ZZ
FRONT BUMPER
EXT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000009161554
CAUTION:
The bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact
with oil.
REMOVAL
1.
Open hood.
2.
Apply protective tape (A) to protect the front fender (1) (LH/RH)
from damage.
3.
Disengage the clips (A), and then remove the radiator cover.
4.
Remove the clips (A) from the top surface of bumper fascia.
5.
Remove the engine under cover. Refer to
EXT-36, "ENGINE UNDER COVER : Removal and Installation"
1.
Bumper side stiffener RH
2.
Bumper side bracket clip RH
3.
Bumper reinforcement
4.
Energy absorber
5.
Blind nut
6.
Bumper fascia
7.
Hole cover
8.
Engine undercover
9.
Bumper side stiffener LH
10. Bumper side bracket clip LH
11.
Bumper bracket RH
12. Bumper bracket LH
13. Rivet
14.
Hood seal assembly (front)
15. Side turn signal lamp RH
16. Side turn signal lamp RH
17.
Front bumper grille
18. Side turn signal lamp LH
19. Bumper side bracket LH
20.
Front bumper finisher B
21. Bumper side bracket RH
22. Bumper bracket cover
23.
Front emblem
24. Front emblem bracket
Refer to
for symbols in the figure.
NNKIA0160ZZ
NNKIA1687ZZ
JMKIA3004ZZ
EXT-16
< REMOVAL AND INSTALLATION >
FRONT BUMPER
6.
Disengage the pawls and the metal clips with the remover tool
(A), and then remove the side turn signal lamps (1) (LH/RH).
Refer to
EXL-52, "Removal and Installation"
.
7.
Remove the fender protector (front). Refer to
EXT-30, "FENDER PROTECTOR : Removal and Installa-
8.
Remove the screws connecting the front fender and the bumper fascia (LH/RH).
9.
Pull bumper fascia (2) in the direction shown in the figure while
lifting up both sides, and then disengage if from the bumper side
bracket (1).
CAUTION:
Never damage the pawls integrated with the bumper fascia
and bumper side bracket during removal.
10. Pull the bumper fascia toward vehicle front, and then disengage it from the bumper side bracket clip on
the LH/RH head lamp lower end.
11. Remove the bumper fascia.
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
12. Remove the following parts after removing the bumper fascia.
• Hood front seal: Refer to
DLK-128, "HOOD ASSEMBLY : Exploded View"
• Front bumper finisher A
Disengage the clips from back of bumper fascia (2), and then remove the front bumper finisher A (1) in
the order 1–2 as shown in the figure.
: Pawl
: Metal clip
NNKIA1688ZZ
: Screw
NNKIA1689ZZ
: Pawl
NNKIA1690ZZ
JMKIA3005ZZ
FRONT BUMPER
EXT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
• Front bumper finisher B
Disengage the pawls from the back of the bumper fascia (1),
and then remove the front bumper finisher B (2).
• Front bumper grille
Disengage the pawls from the back of the bumper fascia, and
then remove the front bumper grille (3).
• Front emblem
Remove the mounting screws, and then remove the front
emblem (3) from the front bumper finisher B (1).
Disengage pawls, and then remove the front emblem bracket
(2).
• Disengage the mounting screws and pawls, and then remove the front emblem.
• Bumper side bracket (LH/RH).
Remove the rivet (A), and then remove the bumper side
bracket (1) from the bumper fascia (2).
NOTE:
Removal and installation of rivet
: Pawl
NNKIA1692ZZ
: Pawl
NNKIA0215ZZ
NNKIA1694ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст