Nissan GT-R. Manual — part 178
INT-14
< REMOVAL AND INSTALLATION >
DOOR FINISHER
7.
Disengage the clips from the door finisher (1) rear side using a
remover tool (A).
CAUTION:
Insert the remover tool between door panel and clip, and
then disengage the clip.
8.
Remove the door finisher rear side lock knob cable (2) and the inside handle cable (1) from the inside
handle (A).
9.
Lift up the door finisher and pull it out toward the passenger
room. Disconnect the connectors (A) and (B) from the door fin-
isher rear side.
10. Remove the door finisher.
11. Remove the front door squawker (BOSE AUDIO WITH NAVIGA-
TION) after removing the door finisher. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
When installing the door finisher, check that the clips are securely fitted in panel holes, and then press
them in.
: Clip
JMJIA2159ZZ
JMJIA2160ZZ
JMJIA2161ZZ
BODY SIDE TRIM
INT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Exploded View
INFOID:0000000009162331
Removal and Installation
INFOID:0000000009162332
CAUTION:
Wrap the tools with shop cloth or tape to prevent damage when using the tools during removal.
REMOVAL
FRONT PILLAR GARNISH
1.
Remove the front body side welt of the front pillar.
1.
Front pillar garnish
2.
Kicking plate outer
3.
Dash side finisher (RH)
4.
Kicking plate inner
5.
Rear side finisher
6.
Rear pillar finisher
7.
Body side welt
8.
Dash side finisher cover
9.
Dash side finisher (LH)
: Clip
: Pawl
: Metal clip
: Always replace after every disassembly
JMJIA2162ZZ
INT-16
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
2.
Insert the remover tool (A) into the clearance between the front pillar garnish (1) and the vehicle body, dis-
engage the metal clips, cut the clip (2) and then remove the front pillar garnish.
KICKING PLATE INNER
1.
Disengage pawls on rear end and side of kicking plate inner
using a remover tool (A).
2.
Disengage remaining pawls while rotating the kicking plate
inner.
3.
Pull kicking plate toward vehicle rear, disengage metal clips, and
then remove kicking plate inner.
DASH SIDE FINISHER
1.
Remove the kicking plate inner.
2.
Remove the clip (A) of the dash side finisher (1).
3.
Disengage and remove the clips of the dash side finisher using
the remover tool (B).
KICKING PLATE OUTER
1.
Remove the center mud guard. Refer to
EXT-34, "Removal and Installation"
: Clip
: Metal clip
NNJIA0016ZZ
: Pawl
JMJIA5244ZZ
: Pawl
: Metal clip
JMJIA5245ZZ
: Metal clip
JMJIA2165ZZ
BODY SIDE TRIM
INT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2.
Disengage and remove the pawls using a remover tool (A) after
removing the clip of kicking plate outer.
BODY SIDE WELT
1.
Remove the kicking plate inner.
2.
Remove the body side welt from the panel flange.
REAR SIDE FINISHER
1.
Remove the kicking plate inner.
2.
Remove the body side welt from the rear side finisher.
3.
Remove the rear seat cushion and the rear seatback. Refer to
SE-56, "Removal and Installation"
4.
Remove rear side finisher fixing clip (2).
5.
Disengage rear side finisher (1) fixing clips and pawls with a
remover tool (A), and then remove rear side finisher.
REAR PILLAR FINISHER
1.
Remove the rear seat cushion and the rear seatback. Refer to
SE-56, "Removal and Installation"
2.
Remove the kicking plate inner.
3.
Remove the rear side finisher and the body side welt of rear pillar finisher.
4.
Remove the rear side finisher.
5.
Remove the front seat belt shoulder anchor. Refer to
SB-6, "SEAT BELT RETRACTOR : Removal and
.
6.
Remove the mounting screw from rear pillar finisher (1) using a screwdriver (A).
7.
Disengage the clips and the metal clips from the rear pillar finisher using the remover tool (A).
INSTALLATION
: Pawl
NNJIA0018ZZ
: Clip
: Pawl
JMJIA5241ZZ
: Clip
: Pawl
: Metal clip
JMJIA5349ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст