Nissan GT-R. Manual — part 277
SE-50
< REMOVAL AND INSTALLATION >
FRONT SEAT
For the seat with side air bag, disconnect the battery cable from the negative terminal after check-
ing that the ignition switch is OFF, wait for at least 3 minutes, and then disconnect the connector.
10. Remove the front seat from the vehicle.
CAUTION:
• Use shop cloths to protect parts from damage during removal and installation.
• Two people must perform removal and installation of the seat assembly to prevent damage or to
keep from dropping it.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Always fix the harness clamp in the normal position.
• Be careful that only driver seat rear inner mounting bolt is different from others among the front seat
mounting bolts.
Disassembly and Assembly
INFOID:0000000009162950
Seatback
Disassembly
1.
Unfasten the seatback trim fastener.
2.
Remove the seatback trim lower retainer.
3.
Remove the seatback (main).
• Remove the seatback cover panel mounting screws, and then
remove the seatback cover panel.
4.
Remove the retainer and hog ring of the seatback assembly (main), and then remove the seatback
assembly (main).
5.
Remove the seat cushion outer finisher outside.
6.
Disconnect the connectors of seat control switch, heater switch, and thigh support (Driver seat only)
switch.
JMJIA2141ZZ
: Metal clip
: Pawl
JMJIA2137ZZ
FRONT SEAT
SE-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
7.
Remove the seat cushion inner finisher outside.
8.
Remove the seatback ornament.
9.
Remove knob.
a.
Press on the seatback surface near the knob mounting portion
inward to expose the fixing portion of the knob.
b.
Disengage knob fixing pawl, and then remove knob.
: Metal clip
: Pawl
JMJIA2138ZZ
: Pawl
JMJIA2139ZZ
JMJIA8391ZZ
: Pawl
JMJIA8392ZZ
SE-52
< REMOVAL AND INSTALLATION >
FRONT SEAT
10. Remove the walk-in lever knob (1) and walk-in lever escutcheon
(2).
11. Disconnect the harness connector.
Driver side
1.
Disconnect the reclining limit switch harness connector (A),
the heater unit harness connectors (B), and the reclining
motor harness connector (C).
2.
Remove the side air bag harness (D).
Passenger side
1.
Disconnect the reclining motor harness connector (E), the
heater unit harness connectors (F), and the reclining limit
switch harness connector (G).
: Pawl
JMJIA2140ZZ
JMJIA5892ZZ
NNJIA0137ZZ
JMJIA5592ZZ
FRONT SEAT
SE-53
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
2.
Remove the side air bag harness (J).
12. Remove the seatback assembly.
Remove the seatback assembly mounting bolts (A).
13. Remove the seat cushion outer finisher inside (front) and the seat cushion outer finisher inside (rear).
14. Remove the seat cushion inner finisher inside (front) and the seat cushion inner finisher inside (rear).
15. Remove the reclining device outer cover (outside) and the reclining device outer cover (inside).
16. Remove the reclining device inner cover (outside) and the reclining device inner cover (inside).
Assembly
Assemble in the reverse order of disassembly.
CAUTION:
Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with
the pad side wire.
Seat cushion
Disassembly
1.
Remove the seat cushion.
• Disconnect the harness connector from the seat cushion heater unit.
• Remove the seat cushion lower surface mounting bolts (A).
• Remove the seat cushion trim retainer from the lower rear of the seat cushion.
NNJIA0146ZZ
JMJIA2153ZZ
JMJIA2136ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст