Nissan GT-R. Manual — part 92
EM-16
< REMOVAL AND INSTALLATION >
CHARGE AIR COOLER
• Install air inlet pipe assembly as follows:
1.
Tighten bolt (A) (temporarily).
2.
Tighten bolt (B) (temporarily).
3.
Tighten bolt (C) (specified torque).
4.
Tighten bolt (A) (specified torque).
5.
Tighten bolt (B) (specified torque).
1
: Air inlet pipe assembly (bank 1)
2
: Air inlet pipe assembly (bank 2)
NNBIA0195ZZ
INTAKE MANIFOLD COLLECTOR
EM-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
INTAKE MANIFOLD COLLECTOR
Exploded View
INFOID:0000000009162837
1.
EVAP hose
2.
Clamp
3.
EVAP tube (bank 1)
4.
EVAP connector hose
5.
EVAP tube (front)
6.
EVAP hose
7.
Vacuum tank (service port)
8.
Clamp
9.
EVAP hose
10.
EVAP canister purge control solenoid
valve
11.
EVAP hose
12. Electric throttle control actuator (bank 1)
13. Gasket
14. Vacuum hose
15. Intake manifold collector
16. Vacuum hose
17. Vacuum tube assembly
18. Vacuum hose
19. Gasket
20. Vacuum hose
21. Electric throttle control actuator (bank 2)
22. Gasket
23. Clamp
24. PCV hose
25. Vacuum hose
26. Vacuum hose
27. Gasket
28. Balance tube
29.
Manifold absolute pressure (MAP)
sensor
30. EVAP tube (bank 2)
31. EVAP connector hose
32. EVAP hose
B.
To centralized under-floor piping
D.
To recirculation valve (bank 1)
E.
To exhaust manifold and turbocharger
(bank 1)
F.
To turbocharger boost control sole-
noid valve
G.
To recirculation valve (bank 2)
H.
To breather separator assembly
NNBIA0221GB
EM-18
< REMOVAL AND INSTALLATION >
INTAKE MANIFOLD COLLECTOR
Removal and Installation
INFOID:0000000009162838
REMOVAL
WARNING:
To avoid the danger of being scalded, never drain engine coolant when the engine is hot.
1.
Remove engine cover. Refer to
2.
Remove recirculation valve and air inlet hose. Refer to
.
3.
Remove electric throttle control actuator as follows:
• Loosen mounting bolts in reverse order as shown in the figure.
CAUTION:
• Handle carefully to avoid any shock to electric throttle
control actuator.
• Never disassemble and adjust electric throttle control
actuator.
NOTE:
• The figure shows the electric throttle control actuator (bank 2)
viewed from the air duct side.
• Viewed from the air duct side, order of loosening mounting
bolts of electric throttle control actuator (bank 2) is the same
as that of the electric throttle control actuator (bank 1).
4.
Remove EVAP canister purge volume control solenoid valve and EVAP tube (front) from intake manifold
collector.
• Loosen mounting bolts in reverse order as shown in the figure.
5.
Remove vacuum hoses, PCV hoses and EVAP hoses, disconnecting each joints
6.
Remove intake manifold collector.
• Loosen mounting bolts in the reverse order as shown in the
figure with power tool.
CAUTION:
Mark the parts with paint in advance of the reinstallation to
prevent misalignment between the intake manifold collector
and intake manifold.
7.
Remove balance tube.
I.
To pressure regulator and fuel hose
assembly
J.
To brake booster
for symbols in the figure.
: Engine front
NNBIA0230ZZ
NNBIA0041ZZ
: Engine front
NNBIA0014ZZ
INTAKE MANIFOLD COLLECTOR
EM-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Loosen mounting bolts in the reverse order as shown in the
figure with power tool.
8.
Remove EVAP tube (bank 1 and bank 2), if necessary.
9.
Remove vacuum tube assembly, if necessary.
10. Remove manifold absolute pressure (MAP) sensor, if necessary.
CAUTION:
Handle carefully to avoid any shock to manifold absolute pressure (MAP) sensor.
INSTALLATION
Note the following, and install in the reverse order of removal.
Balance Tube
• Tighten mounting bolts in numerical order as shown in the figure.
Intake Manifold Collector
• Tighten mounting bolts in numerical order as shown in the figure.
CAUTION:
• Install each part according to the marks put before removal.
• Tighten mounting bolts with care to avoid misalignment in the
intake manifold collector.
• After replacing an intake manifold collector, be sure to adjust the position as instructed below.
1.
Remove intake manifold. Refer to
CAUTION:
Mark the parts with paint with advance of the reinstallation to prevent misalignment between the
intake manifold and cylinder head.
NNBIA0015ZZ
: Engine front
NNBIA0015ZZ
: Engine front
NNBIA0014ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст