Nissan Cube. Manual — part 486
PRECAUTIONS
EXT-9
< PRECAUTION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Precaution for Procedure without Cowl Top Cover
INFOID:0000000009949366
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precaution for Work
INFOID:0000000009949367
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
PIIB3706J
EXT-10
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009949368
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000009949369
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-50397)
NISSAN Squeak and Rattle
Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes clips, pawls and metal clips
Power tool
Loosening bolts, nuts and screws
SIIA0995E
JMKIA3050ZZ
PIIB1407E
FRONT BUMPER
EXT-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
REMOVAL AND INSTALLATION
FRONT BUMPER
Exploded View
INFOID:0000000009949370
JMKIA4087ZZ
EXT-12
< REMOVAL AND INSTALLATION >
FRONT BUMPER
Removal and Installation
INFOID:0000000009949371
REMOVAL
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
1.
Fully open hood assembly.
2.
Remove front grille. Refer to
EXT-17, "Removal and Installation"
3.
Remove fender protector fixing clips and screws to access bumper fascia assembly fixing screw, and then
remove bumper fascia assembly fixing screws (LH/RH).
4.
Remove bumper fascia assembly lower side fixing bolts and clips.
5.
Pull bumper fascia assembly side toward the vehicle side as
shown by the arrows in the figure, and then disengage bumper
fascia assembly from bumper side brackets (LH/RH).
CAUTION:
When removing bumper fascia, 2 workers are required so
as to prevent it from dropping.
6.
Disconnect front fog lamp harness connectors (LH/RH).
7.
Remove bumper fascia assembly.
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
8.
Remove the following parts after removing bumper fascia.
• License plate bracket
• Front bumper side brackets (LH/RH)
• Front bumper finishers (LH/RH) (without front fog lamp models)
• Fog lamps (LH/RH). Refer to
EXL-194, "Removal and Installation"
.
• Bumper spacers
9.
Remove bumper energy absorber.
10. Remove bumper reinforcement.
• Remove radiator core lower stay mounting bolts (A), and then
remove radiator core lower stay.
• Remove bumper reinforcement fixing nuts.
• Partially remove bumper reinforcement right side.
1.
Bumper side bracket RH
2.
Grommet
3.
Bumper reinforcement
4.
Bumper energy absorber
5.
Spacer
6.
Bumper fascia
7.
J nut
8.
Front fog lamp RH
9.
Bumper finisher RH
10. Screw grommet
11.
License plate bracket
12. J nut
13. Bumper bracket cover
14.
Bumper finisher LH
15. Front fog lamp LH
16. Radiator core lower stay
17.
Bumper side bracket LH
: Pawl
JMKIA3812ZZ
JMKIA4093ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст