Nissan Cube. Manual — part 351
EC-290
< DTC/CIRCUIT DIAGNOSIS >
[MR18DE]
P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR
CAUTION:
• Always calibrate the vacuum pump gauge when using it.
• Do not apply below -93.3 kPa (-0.952 kg/cm
2
, -13.53 psi) or pressure over 101.3 kPa (1.033 kg/
cm
2
, 14.69 psi).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace EVAP control system pressure sensor
ECM
Condition
[Applied vacuum kPa (kg/cm
2
, psi)
Voltage
Connector
Terminal
F8
42
(EVAP control system pressure
sensor signal)
Not applied
1.8 - 4.8 V
-26.7 (-0.272, -3.87)
2.1 to 2.5 V lower than above value
P0456 EVAP CONTROL SYSTEM
EC-291
< DTC/CIRCUIT DIAGNOSIS >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0456 EVAP CONTROL SYSTEM
DTC Logic
INFOID:0000000009947401
DTC DETECTION LOGIC
This diagnosis detects leaks in the EVAP line between fuel tank and EVAP canister purge volume control sole-
noid valve, using the negative pressure caused by decrease of fuel temperature in the fuel tank after turning
ignition switch OFF.
If ECM judges there are no leaks, the diagnosis will be OK.
CAUTION:
• Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the
MIL may come on.
• If the fuel filler cap is not tightened properly, the MIL may come on.
• Use only a genuine NISSAN rubber tube as a replacement.
DTC CONFIRMATION PROCEDURE
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0456
Evaporative emission
control system leak
• EVAP system has a leak.
• EVAP system does not operate prop-
erly.
• Incorrect fuel tank vacuum relief valve
• Incorrect fuel filler cap used
• Fuel filler cap remains open or fails to close.
• Foreign matter caught in fuel filler cap.
• Leak is in line between intake manifold and EVAP
canister purge volume control solenoid valve.
• Foreign matter caught in EVAP canister vent con-
trol valve.
• EVAP canister or fuel tank leaks
• EVAP purge line (pipe and rubber tube) leaks
• EVAP purge line rubber tube bent
• Loose or disconnected rubber tube
• EVAP canister vent control valve and the circuit
• EVAP canister purge volume control solenoid
valve and the circuit
• Fuel tank temperature sensor
• O-ring of EVAP canister vent control valve is miss-
ing or damaged
• EVAP canister is saturated with water
• EVAP control system pressure sensor
• Refueling EVAP vapor cut valve
• ORVR system leaks
• Fuel level sensor and the circuit
• Foreign matter caught in EVAP canister purge vol-
ume control solenoid valve
PBIB1026E
EC-292
< DTC/CIRCUIT DIAGNOSIS >
[MR18DE]
P0456 EVAP CONTROL SYSTEM
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
Do you have CONSULT?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
PERFORM DTC CONFIRMATION PROCEDURE-I
With CONSULT
1.
Turn ignition switch ON and select “EVAP DIAG READY” in “DATA MONITOR” mode with CONSULT.
2.
Start engine and wait at idle until “OFF” of “EVAP DIAG READY” changes to “ON”.
NOTE:
It will take at most 2 hours until “OFF” of “EVAP DIAG READY” changes to “ON”.
3.
Turn ignition switch OFF and wait at least 90 minutes.
NOTE:
Never turn ignition switch ON during 90 minutes.
4.
Turn ignition switch ON and select “EVAP LEAK DIAG” in “DATA MONITOR” mode with CONSULT.
5.
Check that “EVAP LEAK DIAG” indication.
Which is displayed on CONSULT?
CMPLT >> GO TO 3.
YET
>> Perform DTC CONFIRMATION PROCEDURE again. GO TO 1.
3.
PERFORM DTC CONFIRMATION PROCEDURE-II
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END.
4.
PERFORM DTC CONFIRMATION PROCEDURE
With GST
1.
Start engine and wait engine idle for at least 2 hours.
2.
Turn ignition switch OFF and wait at least 90 minutes.
NOTE:
Never turn ignition switch ON during 90 minutes.
3.
Turn ignition switch ON.
4.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000009947402
1.
CHECK FUEL FILLER CAP DESIGN
1.
Turn ignition switch OFF.
P0456 EVAP CONTROL SYSTEM
EC-293
< DTC/CIRCUIT DIAGNOSIS >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2.
Check for genuine NISSAN fuel filler cap design.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace with genuine NISSAN fuel filler cap.
2.
CHECK FUEL FILLER CAP INSTALLATION
Check that the cap is tightened properly by rotating the cap clockwise.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Open fuel filler cap, then clean cap and fuel filler neck threads using air blower. Then retighten
until ratcheting sound is heard.
3.
CHECK FUEL FILLER CAP FUNCTION
Check for air releasing sound while opening the fuel filler cap.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK FUEL TANK VACUUM RELIEF VALVE
EC-296, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace fuel filler cap with a genuine one.
5.
CHECK FOR EVAP LEAK
.
Is there any leak in EVAP line?
YES
>> Repair or replace.
NO
>> GO TO 6.
6.
CHECK EVAP CANISTER VENT CONTROL VALVE
Check the following.
• EVAP canister vent control valve is installed properly.
• EVAP canister vent control valve.
EC-274, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace EVAP canister vent control valve and O-ring. Refer to
.
7.
CHECK IF EVAP CANISTER SATURATED WITH WATER
SEF915U
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст