Nissan Cube. Manual — part 1026
WCS
BCM (BODY CONTROL MODULE)
WCS-107
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
CONSULT display
Fail-safe
Tire pressure
monitor warn-
ing lamp ON
Reference
U1000: CAN COMM
—
—
U1010: CONTROL UNIT (CAN)
—
—
B2190: NATS ANTENNA AMP
×
—
B2191: DIFFERENCE OF KEY
×
—
B2192: ID DISCORD BCM-ECM
×
—
B2193: CHAIN OF BCM-ECM
×
—
B2195: ANTI SCANNING
×
—
C1704: LOW PRESSURE FL
—
×
C1705: LOW PRESSURE FR
—
×
C1706: LOW PRESSURE RR
—
×
C1707: LOW PRESSURE RL
—
×
C1708: [NO DATA] FL
—
×
C1709: [NO DATA] FR
—
×
C1710: [NO DATA] RR
—
×
C1711: [NO DATA] RL
—
×
C1716: [PRESS DATA ERR] FL
—
×
C1717: [PRESS DATA ERR] FR
—
×
C1718: [PRESS DATA ERR] RR
—
×
C1719: [PRESS DATA ERR] RL
—
×
C1729: VHCL SPEED SIG ERR
—
×
C1735: IGN CIRCUIT OPEN
—
—
WCS-108
< SYMPTOM DIAGNOSIS >
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
SYMPTOM DIAGNOSIS
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
Description
INFOID:0000000009945543
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
Diagnosis Procedure
INFOID:0000000009945544
1.
CHECK PARKING BRAKE WARNING LAMP
1.
Start the engine.
2.
Check the operation of the brake warning lamp by operating the parking brake.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-93, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
Perform check for the parking brake switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK PARKING BRAKE SWITCH
Perform a unit check for the parking brake switch. Refer to
BRC-79, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-93, "Removal and Installation"
NO
>> Replace parking brake switch. Refer to
.
When parking brake is applied
: ON
When parking brake is released
: OFF
WCS
THE LIGHT REMINDER WARNING DOES NOT SOUND
WCS-109
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE LIGHT REMINDER WARNING DOES NOT SOUND
Description
INFOID:0000000009945545
Light reminder warning chime does not sound even though headlamp is illuminated.
Diagnosis Procedure
INFOID:0000000009945546
1.
CHECK COMBINATION SWITCH (LIGHTING SWITCH) OPERATION
Check that the headlamps operate normally by operating the combination switch (lighting switch).
Do they operate normally?
YES
>> GO TO 2.
NO
>> Refer to
2.
CHECK DRIVER SIDE DOOR SWITCH SIGNAL CIRCUIT
Perform the check for the driver side door switch signal circuit. Refer to
Intelligent Key system) or
DLK-249, "Diagnosis Procedure"
(without Intelligent Key system).
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK DRIVER SIDE DOOR SWITCH
Perform a unit check for the driver side door switch. Refer to
DLK-58, "Component Inspection"
(with Intelligent
DLK-251, "Component Inspection"
(without Intelligent Key system).
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-88, "Removal and Installation"
(with Intelligent Key system) or
155, "Removal and Installation"
(without Intelligent Key system).
NO
>> Replace driver side door switch. Refer to
DLK-225, "Removal and Installation"
(with Intelligent
Key system) or
WCS-110
< SYMPTOM DIAGNOSIS >
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT SOUND
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT
SOUND
Description
INFOID:0000000009945547
• Seat belt reminder warning does not sound.
• Seat belt reminder warning sounds continuously.
Diagnosis Procedure
INFOID:0000000009945548
1.
CHECK SEAT BELT WARNING LAMP
1.
Turn ignition switch ON.
2.
Check the operation of the seat belt warning lamp in the combination meter.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK BCM OUTPUT SIGNAL
Check if the seat belt reminder warning chime is activated by performing BCM active test. Refer to
"BUZZER : CONSULT Function (BCM - BUZZER)"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 3.
3.
CHECK COMBINATION METER INPUT SIGNAL
Check if buzzer switches to proper condition (On/Off) on data monitor of combination meter. Refer to
"CONSULT Function (METER/M&A)"
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-93, "Removal and Installation"
NO
>> Replace BCM. Refer to
BCS-88, "Removal and Installation"
(with Intelligent Key system) or
155, "Removal and Installation"
(without Intelligent Key system).
4.
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) CIRCUIT
Perform the check for the seat belt buckle switch (driver side) circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair harness or connector.
5.
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Perform a unit check for the seat belt buckle switch (driver side). Refer to
WCS-27, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-93, "Removal and Installation"
NO
>> Replace seat belt buckle (driver side). Refer to
SB-8, "SEAT BELT BUCKLE : Removal and Instal-
.
Seat belt (driver side) fastened
: OFF
Seat belt (driver side) unfastened
: ON
Buzzer active condition
: On
Buzzer non-active condition
: Off
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст