Nissan Cube. Manual — part 312
EC-134
< DTC/CIRCUIT DIAGNOSIS >
[MR18DE]
P0011 IVT CONTROL
P0011 IVT CONTROL
DTC Logic
INFOID:0000000009947249
DTC DETECTION LOGIC
NOTE:
If DTC P0011 is displayed with DTC P0075, first perform the trouble diagnosis for
.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is between 10 V and 16 V at
idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE-I
With CONSULT
1.
Turn ignition switch ON and select “DATA MONITOR” mode with CONSULT.
2.
Start engine and warm it up to normal operating temperature.
3.
Maintain the following conditions for at least 6 consecutive seconds. Hold the accelerator pedal as steady
as possible.
4.
Stop vehicle with engine running and let engine idle for 10 seconds.
5.
Check 1st trip DTC.
With GST
Follow the procedure “With CONSULT” above.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE-II
With CONSULT
1.
Maintain the following conditions for at least 20 consecutive seconds.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0011
Intake valve timing control
performance
There is a gap between angle of target
and phase-control angle degree.
• Crankshaft position sensor (POS)
• Camshaft position sensor (PHASE)
• Intake valve control solenoid valve
• Accumulation of debris to the signal pick-up
portion of the camshaft
• Timing chain installation
• Foreign matter caught in the oil groove for in-
take valve timing control
ENG SPEED
1,200 - 2,000 rpm
COOLAN TEMP/S
More than 60
°
C (140
°
F)
B/FUEL SCHDL
More than 4.2 msec
Selector lever
P or N position (CVT)
Neutral position (M/T)
ENG SPEED
1,200 - 3,175 rpm (A constant rotation is maintained.)
COOLAN TEMP/S
More than 65
°
C (149
°
F)
P0011 IVT CONTROL
EC-135
< DTC/CIRCUIT DIAGNOSIS >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
CAUTION:
Always drive at a safe speed.
2.
Check 1st trip DTC.
With GST
Follow the procedure “With CONSULT” above.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009947250
1.
CHECK OIL PRESSURE WARNING LAMP
1.
Start engine.
2.
Check oil pressure warning lamp and confirm it is not illumi-
nated.
Is oil pressure warning lamp illuminated?
YES
>> Go to
.
NO
>> GO TO 2.
2.
CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE
EC-136, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace intake valve timing control solenoid valve. Refer to
.
3.
CHECK CRANKSHAFT POSITION SENSOR (POS)
EC-244, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace crankshaft position sensor (POS). Refer to
4.
CHECK CAMSHAFT POSITION SENSOR (PHASE)
EC-247, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace camshaft position sensor (PHASE). Refer to
.
5.
CHECK CAMSHAFT (INTAKE)
Check the following.
Selector lever
1st or 2nd position
Driving location
Driving vehicle uphill
(Increased engine load will help maintain the driving
conditions required for this test.)
PBIA8559J
EC-136
< DTC/CIRCUIT DIAGNOSIS >
[MR18DE]
P0011 IVT CONTROL
• Accumulation of debris to the signal plate of camshaft (1) rear end
• Chipping signal plate of camshaft rear end
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Remove debris and clean the signal plate of camshaft
rear end or replace camshaft. Refer to
.
6.
CHECK TIMING CHAIN INSTALLATION
Check service records for any recent repairs that may cause timing chain misaligned.
Are there any service records that may cause timing chain misaligned?
YES
>> Check timing chain installation. Refer to
EM-43, "Removal and Installation"
.
NO
>> GO TO 7.
7.
CHECK LUBRICATION CIRCUIT
, “INSPECTION AFTER INSTALLATION”.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Clean lubrication line.
8.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000009947251
1.
CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-I
1.
Turn ignition switch OFF.
2.
Disconnect intake valve timing control solenoid valve harness connector.
3.
Check resistance between intake valve timing control solenoid valve terminals as per the following.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace intake valve timing control solenoid valve. Refer to
.
2.
CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-II
1.
Remove intake valve timing control solenoid valve. Refer to
2.
Provide 12 V DC between intake valve timing control solenoid
valve terminals 1 and 2, and then interrupt it. Make sure that the
plunger moves as shown in the figure.
CAUTION:
Do not apply 12 V DC continuously for 5 seconds or more.
Doing so may result in damage to the coil in intake valve
timing control solenoid valve.
NOTE:
Always replace O-ring when intake valve timing control
solenoid valve is removed.
Is the inspection result normal?
PBIA9557J
Terminals
Resistance
1 and 2
6.7 - 7.7
Ω
[at 20
°
C (68
°
F)]
1 or 2 and ground
∞
Ω
(Continuity should not exist)
JMBIA2107ZZ
P0011 IVT CONTROL
EC-137
< DTC/CIRCUIT DIAGNOSIS >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
YES
>> INSPECTION END
NO
>> Replace intake valve timing control solenoid valve. Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст