Nissan Cube. Manual — part 34
AV
NORMAL OPERATING CONDITION
AV-129
< SYMPTOM DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
RELATED TO VEHICLE ICON
RELATED TO VOICE GUIDANCE
RELATED TO TRAFFIC INFORMATION
The landmark information does
not correspond to the actual in-
formation.
This may be caused by insufficient or incorrect data on the
map SD-card.
Updated information will be included
in the next version of the map SD-
card.
The suggested route does not
exactly connect to the starting
point, waypoints, or destina-
tion.
There is no data for route calculation closes to these loca-
tions.
Set the starting point, waypoints and
destination on a main road, and per-
form route calculation.
Symptom
Possible cause
Possible solution
Symptom
Possible cause
Possible solution
Names of roads and locations differ
between 2D and 3D view.
This is because the quantity of the displayed in-
formation is reduced so that the screen does
not become difficult to read. There is also a
chance that the names of roads or locations
may be displayed several times, and that the
names appearing on the screen may be differ-
ent because of a processing procedure.
This is not a malfunction.
The vehicle icon is not displayed in
the correct position.
The vehicle was transported after the ignition
switch was pressed off, for example, by a ferry
or car transporter.
Drive the vehicle for a while on a road where
GPS signals can be received.
The position and direction of the vehicle icon
may be incorrect depending on the driving en-
vironments and the levels of positioning accu-
racy of the navigation system.
This is not a malfunction. Drive the vehicle for
a while to automatically correct the position
and direction of the vehicle icon.
When the vehicle is travelling on a
new road, the vehicle icon is located
on another nearby road.
The system automatically places the vehicle
icon on the nearest available road, because the
new road is not stored in the map data.
Updated road information will be included in
the next version of the map SD-card.
The screen does not switch to the
night screen even after turning on
the headlights.
The daytime screen was set the last time the
headlights were turned on.
Set the screen to the night screen mode using
<Day/Night> when you turn on the headlights.
The map does not scroll even when
the vehicle is moving.
The current location map screen is not dis-
played.
Press “MAP”.
The vehicle icon is not displayed.
The current location map screen is not dis-
played.
Press “MAP”.
The location of the vehicle icon is
misaligned from the actual position.
When using tire chains or replacing the tires,
speed calculations based on the speed sensor
may be incorrect.
Drive the vehicle for a while [at approximately
30 km/h (19 MPH) for about 30 minutes] to
automatically correct the vehicle icon posi-
tion.
The map data has an error or is incomplete (the
vehicle icon position is always misaligned in the
same area).
Updated road information will be included in
the next version of the map SD-card.
Symptom
Possible cause
Possible solution
Voice guidance is not available
In some cases, voice guidance is not available even
when the vehicle should make a turn.
This is not a malfunction.
The vehicle has deviated from the suggested route.
Go back to the suggested route or request
route calculation again
Voice guide is set to off.
Turn voice guidance ON.
Route guidance is set to off.
Route guidance is set to ON.
The guidance contact does not
correspond to the actual condi-
tion.
The contact of voice guidance may vary, depending on
the types of intersections at which turn are made.
Follow all traffic rules and regulations.
AV-130
< SYMPTOM DIAGNOSIS >
[AUDIO WITH NAVIGATION]
NORMAL OPERATING CONDITION
RELATED TO TELEPHONE
RELATED TO HANDS-FREE PHONE
Symptom
Possible cause
Possible solution
The traffic information is
not displayed
The traffic information is not set to on.
Set the traffic information to on.
You are in an area where traffic information is not avail-
able
Scroll to an area where traffic information is avail-
able
You have not subscribed to XM NavTraffic or, your sub-
scription to XM NavTraffic has expired.
Check your subscription status of XM NavTraffic.
The map scale is set at a level where the display of icons
is impossible.
Check that the map scale is set at a level in which
the display of icons is possible.
With the automatic de-
tour route search ON,
no detour route is set to
avoid congested areas.
There is no faster route compared to the current route,
based on the road network and traffic information.
The automatic detour search is not intended for
avoiding traffic jams. It searches for the fasted
rote taking into consideration such things as traffic
jams.
The route does not
avoid road section with
traffic information stat-
ing it is closed due to
road construction.
The navigation system is designed not to avoid this
event because the actual period of closure may differ
from the declared roadwork period.
Observe the actual road condition and follow the
instructions on road for detour when necessary. If
the road closure is for certain, use detour function
and set the detour distance to avoid the closed
road section.
Traffic information dis-
played differs from in-
formation from other
media (e.g. radio).
Other media may use different information sources.
Observe the actual road conditions and regula-
tions. Always observe safe driving practices and
follow all traffic regulations.
Symptoms
Cause and Counter measure
System fails to interpret the com-
mand correctly.
1. Ensure that the command format is valid.
2. Ensure that the command is spoken after the tone.
3. Speak clearly without pausing between words and at a level appropriate to the ambient noise
level in the vehicle.
4. Ensure that the ambient noise level is not excessive (for example, windows open or defroster
on).
NOTE:
If it is too noisy to use the phone, it is likely that the voice commands will not be recognized.
5. If more than one command was said at a time, try saying the commands separately.
6. If the system consistently fails to recognize commands, the voice training procedure should be
carried out to improve the recognition response for the speaker.
Refer to
AV-84, "Diagnosis Description"
.
The system consistently selects
the wrong entry from the phone
book.
1. Ensure that the phone book entry name requested matches what was originally stored. This
can be confirmed by using the “List Names” command.
2. Replace one of the names being confused with a new name.
AV
NORMAL OPERATING CONDITION
AV-131
< SYMPTOM DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Symptom
Cause and Counter measure
Does not recognize cellular phone connection. (No connection is
displayed on the display at the guide.)
Some Bluetooth
®
enabled cellular phones may not be recognized
by the in-vehicle phone module. Refer to “RELATED TO HANDS-
FREE PHONE (Check Compatibility)” of HANDS-FREE PHONE
SYMPTOMS.
Cannot use hands-free phone
Customer will not be able to use a hands-free phone under the fol-
lowing conditions.
• The vehicle is outside of the telephone service area.
• The vehicle is in an area where it is difficult to receive radio
waves; such as in a tunnel, in an underground parking garage,
near a tall building or in a mountainous area.
• The cellular phone is locked to prevent it from being dialed.
NOTE:
While a cellular phone is connected through the Bluetooth
®
wire-
less connection, the battery power of the cellular phone may dis-
charge quicker than usual. The Bluetooth
®
Hands-Free Phone
System cannot charge cellular phones.
The other party's voice cannot be heard by hands-free phone.
When the radio wave condition is not ideal or ambient sound is too
loud, it may be difficult to hear the other person's voice during a
call.
Poor sound quality
Do not place the cellular phone in an area surrounded by metal or
far away from the in-vehicle phone module to prevent tone quality
degradation and wireless connection disruption.
AV-132
< REMOVAL AND INSTALLATION >
[AUDIO WITH NAVIGATION]
NAVI CONTROL UNIT
REMOVAL AND INSTALLATION
NAVI CONTROL UNIT
Removal and Installation
INFOID:0000000009949636
REMOVAL
1.
Remove cluster lid C. Refer to
2.
Remove NAVI control unit screws, then disconnect NAVI control unit connector and remove NAVI control
unit.
3.
Remove bracket screws to remove NAVI control unit.
INSTALLATION
Install in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст