Nissan Cube. Manual — part 115
BRC-110
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
WHEEL SENSOR
REMOVAL AND INSTALLATION
WHEEL SENSOR
FRONT WHEEL SENSOR
FRONT WHEEL SENSOR : Exploded View
INFOID:0000000009950043
NOTE:
The above figure (front side) shows left side. Right side is the mirror image.
FRONT WHEEL SENSOR : Removal and Installation
INFOID:0000000009950044
REMOVAL
1.
Remove the fender protector. Refer to
EXT-21, "FENDER PROTECTOR : Exploded View"
.
2.
Remove the wheel sensor from steering knuckle.
CAUTION:
Never twist sensor harness as much as possible, when removing it. Pull wheel sensors out with-
out pulling sensor harness.
3.
Remove the wheel sensor harness from vehicle.
CAUTION:
Never twist sensor harness as much as possible, when removing it. Pull wheel sensors out with-
out pulling sensor harness.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Make sure there is no foreign material such as iron chips on and in the mounting hole of the wheel sensor.
1.
Front LH wheel sensor
2.
Front LH wheel sensor harness con-
nector
A.
Color line
: Vehicle front
Refer to
for symbols in the figure.
JPFIC0038GB
WHEEL SENSOR
BRC-111
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• Make sure no foreign material has been caught in the sensor rotor. Remove any foreign material and clean
the mount. Replace the wheel sensor if necessary.
• When installing wheel sensor, be sure to press rubber grommets in until they lock at locations shown above
in the figure. When installed, harness must not be twisted.
REAR WHEEL SENSOR
REAR WHEEL SENSOR : Exploded View
INFOID:0000000009950045
REAR WHEEL SENSOR : Removal and Installation
INFOID:0000000009950046
REMOVAL
1.
Remove wheel sensor from wheel hub and bearing assembly.
CAUTION:
Never twist sensor harness as much as possible, when removing it. Pull wheel sensors out with-
out pulling sensor harness.
2.
Remove wheel sensor harness from vehicle.
CAUTION:
Never twist sensor harness as much as possible, when removing it. Pull wheel sensors out with-
out pulling sensor harness.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Make sure there is no foreign material such as iron chips on and in the mounting hole of the wheel sensor.
• Make sure no foreign material has been caught in the sensor rotor. Remove any foreign material and clean
the mount. Replace the wheel sensor if necessary.
• When installing wheel sensor, be sure to press rubber grommets in until they lock at locations shown above
in the figure. When installed, harness must not be twisted.
1.
Rear LH wheel sensor
2.
Rear LH wheel sensor harness con-
nector
: Vehicle front
Refer to
JPFIC0039GB
BRC-112
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
SENSOR ROTOR
SENSOR ROTOR
FRONT SENSOR ROTOR
FRONT SENSOR ROTOR : Removal and Installation
INFOID:0000000009950047
CAUTION:
Sensor rotor cannot be disassembled. Remove the sensor rotor together with hub bearing assembly.
REMOVAL
Remove the wheel hub and bearing assembly. Refer to
INSTALLATION
Install the wheel hub and bearing assembly. Refer to
FRONT SENSOR ROTOR : Disassembly and Assembly
INFOID:0000000009950048
Sensor rotor cannot be disassembled. Remove the sensor rotor together with hub bearing assembly.
REAR SENSOR ROTOR
REAR SENSOR ROTOR : Removal and Installation
INFOID:0000000009950049
CAUTION:
Sensor rotor cannot be disassembled. Remove the sensor rotor together with hub bearing assembly.
REMOVAL
Remove the wheel hub and bearing assembly. Refer to
.
INSTALLATION
Install the wheel hub and bearing assembly. Refer to
REAR SENSOR ROTOR : Disassembly and Assembly
INFOID:0000000009950050
Sensor rotor cannot be disassembled. Remove the sensor rotor together with hub bearing assembly.
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-113
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Exploded View
INFOID:0000000009950051
Removal and Installation
INFOID:0000000009950052
REMOVAL
1.
Disconnect the battery cable from negative terminal.
2.
Remove cowl top cover and extension cowl top. Refer to
3.
Drain brake fluid. Refer to
4.
Disconnect ABS actuator and electric unit (control unit) harness connector.
5.
Loosen brake tube flare nuts, and then remove brake tubes from ABS actuator and electric unit (control
unit). Refer to
BR-20, "FRONT : Exploded View"
CAUTION:
Never scratch the flare nut and the brake tube.
6.
Remove ABS actuator and electric unit (control unit) and bracket from vehicle.
CAUTION:
• Never apply excessive impact to ABS actuator and electric unit (control unit), such as dropping
it.
• Never remove actuator by holding harness.
7.
Remove bracket and bush from ABS actuator and electric unit (control unit).
1.
ABS actuator and electric unit (control
unit)
2.
Harness connector
3.
Bushing
4.
Bracket
A.
To front LH brake caliper
B.
To rear RH wheel cylinder
C.
To Rear LH wheel cylinder
D.
To front RH brake caliper
E.
To master cylinder secondary side
F.
To master cylinder primary side
: Vehicle front
Refer to
for symbols in the figure.
JPFIC0061GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст